Jump to content
SAU Community

Recommended Posts

I bought the matic-J oil the other day was gonna do it myself today.. from the info i have found dropping the oil out the drain plug will only remove half then i can just top back up the exact amount i removed.

Or should i take it to a mech and get them to flush and fill with full amount??

im only asking coz i found mixed results, some saying not good to flush the system(unwanted pressure..etc) and others saying not good to just drain as your not removing all the old stuff..

I just want to know what others have done.

either way im happy to do myself, or take to mech as i have bought the expensive stuff.... matic-J is like the cost of liquid gold. :ermm::)

thanks

sorry to start new thread.. but the M35 info one is getting massive and without categories gets hard to find stuff..

Link to comment
https://www.sau.com.au/forums/topic/334650-m35-transmission-fluid-change/
Share on other sites

This is for S1 but pretty sure M35 is the same (i.e. the sump will hold a lot less than half). You could do it without dropping the sump. This way you are just using the stock auto's pump (it has been suggested that the pwer flushing system of the auto shops can damage seals but I can't verify that):

Get yourself an auto sump gasket kit and a 20L drum of (ideally) quality synthetic atf. You need 12 to 14L for the auto and you can use the rest for your attessa and power steering. Drain the sump and drop it (easier said then done - you will have to support the box and remove the rear mounting). You will only get betweeen 1 and 2 litres this way. Check that the new internal filter is exactly the same (otherwise the sump won't go back on) and if not either modify the new one to suit or clean the old one and put it back. Put 2L of fresh oil down the dip stick tube.

Then pull a hose off the trans oil cooler and run the engine until you have pumped out 2L into a container. Pour 2L of new oil down the dipstick tube and repeat until you get clean oil coming out. This will take 12 to 14L in total.

I bought the matic-J oil the other day was gonna do it myself today.. from the info i have found dropping the oil out the drain plug will only remove half then i can just top back up the exact amount i removed.

Or should i take it to a mech and get them to flush and fill with full amount??

im only asking coz i found mixed results, some saying not good to flush the system(unwanted pressure..etc) and others saying not good to just drain as your not removing all the old stuff..

I just want to know what others have done.

You should be able to get quite a lot by draining (about 4L or so), unfortunately ours takes over 8L, so you could do it again the following weekend which is effectively just diluting the old oil with fresh stuff or alternatively take it to Nissan for a transmission flush and take the price of the oil off the bill (you will lose $$ though).

hmmm.... while I think about it, would something like the Liquivac work for removing all the transmission oil?

matic-J is like the cost of liquid gold. :D:(

Maybe look at getting some Matic-S from the US? We have yet to receive it in Australia, but it is the 100% synthetic replacement to Matic-J.

sorry to start new thread.. but the M35 info one is getting massive and without categories gets hard to find stuff..

Agreed.....

couldnt agree more with another forum for m35 stuff.

I keep confusing peoples comments about S1's and S2's until i notice either C34 in their list of cars or their avatar of a c34.. and im like meh doesnt apply to my s1!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...