Jump to content
SAU Community

Hel Stainless Steel Braided Clutch Line Group Buy


Recommended Posts

  • Replies 187
  • Created
  • Last Reply

Top Posters In This Topic

Ok, the lines are getting picked up by Fedex tomorrow meaning I shall have them late next week some time.

One small hicup, the GTT lines are not yet made and will be sent seperately in a weeks time so every one doesn't have to wait. Hope that is ok.

Cheers

LINES ARE HERE!

I'll start getting them ready today and try and mail them out tomorrow before work or worst case scenario on Thursday.

LINES ARE HERE!

I'll start getting them ready today and try and mail them out tomorrow before work or worst case scenario on Thursday.

Cheers Phil

They have all been sent out today. People in QLD should probably receive them tomorrow and every where else on Monday or Tuesday.

Blazk, Pintaline and Gimps-34 I will let you guys know when the GTT clutch lines have arrived to me.

Cheers guys

is the clutch line meant to go from master to slave cylinder or master to separation box?? any problems with by-passing the separation box??

I'm not really sure on how the GTR setup works. For reference the GTST line is quite a bit longer than the GTR line.

Edited by PM-R33

Got it today with thanks mate :rant:

I'm not sure where it's meant to go.... looks too long to replace just the factory rubber line, too short to get rid of the "block"... I'm certain it will all come to light soon enough though! :P

Thanks again, great smooth GB :yes:

Too easy Ben, glad to see the QLD guys are getting them today.

Yeah I wasn't really sure on what the GTR line replaced since it was a different length than the GTST one. But I figured you GTR boys have some weird funky setup due to the AWD hence it being different :P

I think the GTST one replaces the block, but I shall soon see.

Got mine as well :D

I'm pretty sure it replaces the block, if not I'm gonna try my best to make it replace the block

Thanks again Phil. Must be hecktic at your place trying to organise all these group buys :)

Hahaha cheers guys. The people at the post office I go to always act so suspicious every time I rock up with two boxes full of express post satchels lol.

I was under the impression via the HEL website that the GTR lines were supposed to replace the whole lot, direct line from master to slave?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...