Jump to content
SAU Community

Recommended Posts

sorry not real sure which but my car has a hybrid i/c and apexi pod.I thought having a heat shield would prevent hot air from the engine bay, whilst having that extra hole where the standard piping used to be having air directed from there onto the pod.what u reckon or is it pointless

Link to comment
https://www.sau.com.au/forums/topic/34123-heat-shield-ideas/#findComment-685093
Share on other sites

  • 10 months later...
  • 3 months later...

This is how the heat sheild was set up on my last R33 it also had a cold air intake from underneath the front wheel/spoiler and was very effective as you all know how much heat the engine bay produces, im currently making a new one for my new car due to the intercooler pipes being in a different place etc...

The easiest way to get one would be to make it yourself since most cars have a different set up. Its quite easy as im making my second one as we speak.

1.ust take a cut out of cardboard and put it roughly where you want it.

2.Mark all the areas where the pipes are and anything else that is in the way.

3.Cut them out and check it again cutting and shaping it as you go.

4.You can also put bends etc... in the cardboard and tabs etc.. for bolts and so on.

5.Now you have a template, just take it and cut it out of what ever you like(i used 3mm polished alliminium), then bend it up and presto.

It may not fit perfect first time but if you have a real good stencil it should work pretty well.

I also added a little bend to mine to make it look factory.

Cheers hope this helps and if anyone else has some good idea's then lets hear them.

2 ingredients needed for cold air intake.

100-130mm PVC elbow.

Angle grinder.

As was said above u need to make a shield for the barrier, which can be done with some cardboard for template and some aluminium sheeting. Then cut a hole in front left wheel arch and it will be able to sit right behind the bumper. DO NOT CUT STRUCTURAL STEEL, bad plan, minor cutting only.

Or you could buy one that is made for it :P

Your other option is to find some good vacuum hose and mover the whole filter down into the bumper but that might get a little wet on rainy days. You willl still need some sheilding though.

asylum, i uses heat shield, i got a shit load from clark-rubber, they have two types a really think one or just normal, i basicly cut it with a knife and just suck it in there (the car come with like a metal plate which goes over the top),

If you dont have a fmic i have been told it is pointless as there is no direct air-intake as such, basicly your ment to uses the free hole (one which was uses for stock side-mount) and get a PVC pipe and direct the air in through the hole

man i bought one for $150.... i will c if i can find the guys car.... (paul (gtst vspec) its the guy that u gave me the car 4) he lives near bunbry...... they sell his ones at extreme machines for like $700... which is bs....

they are made of aluminium...... side and the top of hte box is also aluminium..... for those that are looking they are for the r33 only but

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...