Jump to content
SAU Community

Recommended Posts

I've spotted a Millenium Jade GTR for sale on Drive.com.au

R34 M-Spec Nur with only 25000 km's, asking $75000.

There's only 250 world wide.

Isn't this too cheap for what it is.

There's another black one in NZ going for $150000

If my wife would allow it, I'd be off to Aussie tomorrow.

Who elso thinks this is a bargain ?

Link to comment
https://www.sau.com.au/forums/topic/341342-r34-m-spec-nur-for-75000/
Share on other sites

the pic of the rear of the car the GTR badge is in the wrong spot and the nissan badge is not quite straight may have had a respray, the next pic the close up pic off the right rear side the GTR badge is in the correct spot looks like a different car not sure why they would of done that, and that car looks to have rear led tail lights

2 Rear shot photos look to be different car as posted above.

LED lights

M on the mspec is black on one and not the other.

2 pictures were at different locations (could just be because) - red in the right top corner is not evident in the whole rear shot.

- I make the above point cause, every other photo was taken at the same location. You can see the fence/green outline of the fence in every other photo.

Nice car, does it have books :)?

I would say that is decent, a V-Spec II Nur goes for about $80K, give or take...

The pics of the rear in the link are from different cars...

Inquire / get the VIN Number and do a FAST Check.

When the VIN checks out to be correct, take a look in person.

After I drove 1, M-Spec Nur's will not disappoint.

Very smooth / refine and if it is stock, it is asking for mods to free out the performance.

The dealer selling this car is www.allimports.com.au . I know the owner of the place and can honestly say he brings in some very clean cars. He sold a champagne gold m-spec nur not long ago, aswell as a white v-spec ii nur for the exact same price both with low kms.

The dealer selling this car is www.allimports.com.au . I know the owner of the place and can honestly say he brings in some very clean cars. He sold a champagne gold m-spec nur not long ago, aswell as a white v-spec ii nur for the exact same price both with low kms.

Someone disagrees with you...

http://ozvr4.com/forums/showthread.php?980...ght=all+imports

Can always enquire about them or any dealers reputation at NSW Dept of Fair Trading LINK FOR ENQUIRES.

This one is even better, worth joining just to read, auction reports compared to vehicle listed by dealer are good. Others there as EVO OZ have had a few run ins with certain dealers.

BEWARE OF "EDDIE AND JIMMY" 25 pages worth LINK

The dealer selling this car is www.allimports.com.au . I know the owner of the place and can honestly say he brings in some very clean cars. He sold a champagne gold m-spec nur not long ago, aswell as a white v-spec ii nur for the exact same price both with low kms.

Yeah right,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...