Jump to content
SAU Community

Recommended Posts

Ok. I thought I'd chuck this in here because of the thread title:

TUSCAN STYLE BARRAMUNDI ON SLOW ROASTED TOMATOS ( THE SAUCE IS THE KEY icon_biggrin.gif )

TOMATOS

Pre-heat the oven to 140c

Cut the top and the tail of 4 tomatos off. Drizzle tomatos with olive oil, season with sea salt and a little pepper.

( Cooking time about 1hr 20 mins ) The can be cooked on a higher heat if you're in a rush but doing it this way you'll intensify the flavour more, almost like a large semi-sundried tomato. ( If you don't like skins, blanch them in hot water briefly and peel off skins )

SAUCE

In a sauce pan melt approximately 50 grams of butter. Cook butter until it starts to go a light brown colour ( Browning the butter will add a more nutty type flavour ). Add 2 cloves of garlic (finely chopped), 1 small chilli ( finely chopped - you can use a little capsicum if you don't like heat), ginger( grated about a teaspoon ) cook in the butter for about 20 seconds to release the oils then add baby capers about a tablespoon full along with some powdered star anise about 1/4 teaspoon, a large pinch worth.

Add white wine 100ml, cook alcohol off. Then add 100ml of orange juice, about 50ml of teriyaki sauce ( This will be the main salt content so add more or less to taste.

Reduce sauce down to about half its volume, it should start to really get a glisten/sheen to it. Probably about 15 mins cooking time.

Once the sauce is ready and the tomatos are almost ready do the fish.

2 large portions of Barramundi (3-400g's ea) thick cut from a fillet and squared off, any bloodline removed. The fishmonger can do all the main filleting/pinboning.

Pre-heat frying pan ( Hot )

Remove tomatos from over and turn up to 200c

Pat down the skin with a paper towel and season skin side with a little salt and white pepper.

Put olive oil in pan and place fish skin down ( Cook for approx 2 minutes ) Check skin, if starting to go crispy, turn fish over and put straight in the oven. Cook for about 6-7 mins. Or until the flesh starts to separate a little.

Plate up

Put 2 tomatos on the plate and dress with a little sauce. Place the fish directly on top, building a little tower. Dress with more sauce to taste ( I like lots )

To give the dish texture I also chuck on the plate some chopped pan roasted cashews. The flavour and texture really add something to the dish.

A pinch of smoked paprika around the edge of the plate is you want to tart up the look a bit more, the flavour also marries well - Finely chopped basil will also add colour and flavour

Edited by ArdentEagle

noted and emailed to wife :thumbsup:

Cheers mate. It one of my wifes/best mates favourite dishes that I make. Tell your wife to keep in mind I like things fairly acidic so depending on taste and if extra sugar is already added to the orange juice she may need to add a little bit of sweetener for balance. Demerera sugar or honey would be best imo.

If its a fan forced over maybe set it to 110-120 for that amount of time with the tomatos

Good work, Eagle. Its been a while since we've had someone actually post a recipe in here. Barramundi is a great fish to eat too, not to many bones.

Thanks buddy..... I love Barra, the taste, the texture. A brilliant fish!

I've discovered it bloody hard to write our a recipe so its easy to follow. I normally just get in the kitchen and cook.

Edited by ArdentEagle

I thought you were saving for my turbo kit, looks like the missus is on to you mate, I hope she isn't reading these threads... :P

Trying to...and failing :P

Whenever she sees me browsing IM she's like "what are you buying now!!" :rolleyes:

I tell her I'm browsing for stuff to get for the Grandis (NA4W)...hehe

Edited by ironpaw

Finally got my mig/tig welder today, time to get my fabrication on.

So who wants blast pipes, drift pipes or decat "test" track only pipes?

me .....I want a side pipe setup for track.....I want flames out the side like below. :P

post-37023-0-85601600-1311718531_thumb.jpg

Edited by Jetwreck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...