Jump to content
SAU Community

Recommended Posts

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/343240-r33-gt-r-best-first-mod-option/
Share on other sites

remove boost restrictor,good air filter, whole exhuast with good metal cat, cam gears, boost controller max 18psi on stock comp and injectors, then comp and z32 afms, then injectors and fuel pump, turbos, cams and full engine build, i've done or in process of doing in this order

Thanks guys, much appreciated.

Some of those will have to wait until the bank account recovers from buying the car! LOL

Just curious, will I notice much of a difference if I remove the boost restrictor now?

Also how safe is this given the ceramic stock turbo wheels? And do I need a boost gauge (other than the stock one) and a manual boost controller?

from memory (tuned one awhile back and was not to far off one with 3" cat back) the std 33 GTR exhaust was not too bad at the power levels these make (JDM cats are good, compliance cats are not) boost restrictor removal and tune if your not into more noise from the rear.

Removing the bung improves your air intake... I dont know how is that bad. Plus you can hear the induction and bov sound more and its legal!

But anyway, like everyone else said. Get someone good to look after your car if you're not very mechanically minded. Probably good to get the exhaust system done first (front pipe, cat and catback) and ecu + boost (around 12-14psi should be fine on stock turbo). Read more on the force induction section and you'll find most of your questions already answered.

totally depends on budget

ensure your brakes are up to scratch first, & an oil change & spark plugs

ensure the HICAS fluid is also correct.

next i would

(assuming all is stock)

replace the factory intake - replace with ARC if budget allows or Apexi.

replace factory exhaust / muffler withi something like HKS Hi silent if your wanting a quiet muffler or blitz nur if not

take out the cat , and replace with decat

boost controller run at 1bar.

then dyno run to ensure all is well

fuel pump woudl also be on my agenda

It seems when I am reffering to the boost restrictor others are talking about something to do with the airbox etc.

I am talking about the boost restrictor that is in one of the vaccuum hoses and is marked by the yellow line. It restricts boost to 9psi from the factory and when removed raises the boost to 14psi.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

Where is the HICAS fluid located? The manual that came with the car is pretty crap, looks like omething that did not come from the factory.

There is no HICAS fluid on a R33 or R34 the HICAS rack is electric not hydraulic. And do not waste your money on replacing intake pipes... get everything fixed and ensure everything functions correctly. That will cost you enough before you start spending it on handling better and going faster!

Hi all,

Just wondering what everyone thinks the best first performance mod is for a R33 GT-R?

I know with my XT Forester the single best mod performance wise was swapping the stock exhaust system for a 3" TBE.

Would you say the same for the R33 GT-R?

Cheers.

dont do it, its a slippery slope :blink:

i would personally get everything checked over, stick it on a dyno and check afr, compression if not already checked, service and replace anything thats worn like pads, rotors, tyres etc, after all that, you have a good base to start doing lil mods, i wouldnt take the restrictor out if u running stock turbos, its still a nice car, enjoy it and do the easiest and cheapest mods first so your wallet doesnt have a heart attack

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...