Jump to content
SAU Community

Recommended Posts

Last week when down to a 1/4 of a tank, my fuel completely cut out when i was making a right hand turn. Oce i brought the car to a safe stop. I turned the ignition off and let it sit. It started back up first time, and i got it to a petrol station where i re filled the car. That seemed to fix the problem.

However today when i was taking a large right hand bend on a freewy with 1/3 of tank left the car did the same thing however it kicked back in without any safety issues.

I have also up untill recently had a fuel gage that was playing up and would say that i have an empty tank, despite the tank nearly being full.

I have a 1999 Series 2 Rs4 auto, it is completely stock. I have just had a major service done to the car. I always fill it up with 98ron petrol.

Just trying to find out peoples opinions on what they think the issue could be?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/
Share on other sites

fix what you know is broken first, then look at maybe problem second unitl then keep car full and guess fuel level from kms on trip meter, don't rely on a gauge you know is playing up.

if you are sure it only does it when fuel is low could be loose pump intank and when you go around right turn it sways out of the fuel

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5538024
Share on other sites

The fuel pickup is on the right hand side so when you turn right the fuel goes left away from the pickup. This should not normally be a problen unless the tank is quite empty so there are two things that come to mind... the pickup is not fitted correctly to the pump so that it doesn't sit right on the bottom of the tank or maybe the sock and or the tank is clogged with dirt. Either way it could be a good idea to pull the pump out and if it is the original not a bad idea to put in a new one at this stage and anyway change the fuel filter in the engine bay if you haven't already. BTW I have a fuel guage sender unit if you think you need one although it might be easier to get one locally if someone is wrecking a Stagea near you.

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5538237
Share on other sites

Had same problem on corners, did the constant 12v wiring mod, hasnt happened since. My theory is that the fuel pump was stalling internaly somehow under g load, related to the low voltage from the stock wiring setup.

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5538526
Share on other sites

you sure it's completely stock? if you haven't changed the fuel pump i'm guessing someone else replaced the fuel pump, check it out. The stock sock for the fuel pump was probably replaced. (stock sock is obviously longer compared to the walbro ones aftermarket/etc.) Also, see if the fuel pump cradle is placed properly on the bracket where it was originally hanging onto. I've had this problem before as well but now i've fixed it.

http://www.skylinesaustralia.com/forums/To...mp-t253097.html

Edited by JnJ
Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5539173
Share on other sites

As i have very little knowledge about my car.

If it is the fuel tank intake, how much would it cost to replace?

Also i just had a major service completed on my car so i'm assuming the filters would have been replaced.

Will an auto-electrician be able to fix the problem with my fuel gage?

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5539183
Share on other sites

It is a fairly straightforward job to have a look in the tank and fuel pump assembly. I would bet there is something that is fairly simple wrong with a pump being reinstalled incorrectly and that might account for both issues.

A mechanic should have no trouble checking this but by the same token it is possible to DIY this and/or get some help locally from a forum member.

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5539235
Share on other sites

So I parked my car, and now it wont start. It was 10.30 at night so I called the RACV. He said, that there was very little pressure in the fuel line, he was struggling to hear the fuel pump as well. There was like 40 litres of Premium petrol in the tank when it didn't start.

Looks like i am getting it towed, but i am still unsure on where to take the car. It is parked in the eastern suburbs of Melbourne.

FML...

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5541254
Share on other sites

A fella I worked with, had a weird issue with his car, when it had less than 1/4 of a tank, it would just stop after a while. Really random but always with low fuel.

Turned out his fuel pump was knackered (500,000kms!) and when the tank was low, the heatsoak in the smaller volume of fuel being recirculated, would cause it to nip up, and stop.

With a full tank, it would cool the pump ok, but eventually it died completely. Also had the low fuel pressure issue that you're describing, but when left for an hour or so, it would start, & run flawlessly. Drove me bloody mad!

Check the pump.

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5541280
Share on other sites

Just get a new pump anyway if its the original you need a new (not second hand unless you're broke) pump. Walbro will be fine or Bosch 040 or more expensive if you want. Try also to get it direcxtly wired for full battery voltage (several how tos on this site or a sparky should be able to sort it easily).

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5541438
Share on other sites

Had same problem on corners, did the constant 12v wiring mod, hasnt happened since. My theory is that the fuel pump was stalling internaly somehow under g load, related to the low voltage from the stock wiring setup.

How do I find out what this wiring mod is????

Link to comment
https://www.sau.com.au/forums/topic/343460-fuel-issues/#findComment-5542969
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...