Jump to content
SAU Community

Recommended Posts

G'day guys,

Been doing a fair bit of reading on SAU and other places regarding blow-by, catch-cans and the good ol' PCV valve.

For now, let's assume we don't want to vent to atmosphere - i know we probably do, but for this argument, let's pretend we don't :)

It seems there's two trains of thought regarding blocking the PCV. Some say you need to leave it intact if you're not venting to atmo, others say it's best to block it.

I'm trying to get my head around which is actually better, and why.

The way I understand it, in 'stock' configuration, the PCV allows the engine to breathe into the intake manifold while under vacuum, and closes under boost, when it can breathe via the exhaust side hose into the pre-turbo intake pipe.

If we were to just block the PCV, and change nothing else, wouldn't it just mean that all of the breathing would happen via the turbo inlet pipe? Aside from the large amounts of oil that would be pushed into the intake, are there any other issues with this?

If we then put a catch can with a decent oil/air separator setup in between the rocker cover and the intake pipe, wouldn't this allow the engine to breathe as required, without pushing any oil directly into the intake manifold and reducing the octane rating?

I figure I must be missing something here - mainly because of this: Nissan put a PCV valve in there for a reason - it must be required for something I'm overlooking! :rofl:

Link to comment
https://www.sau.com.au/forums/topic/345545-oil-catch-canpcv-setups/
Share on other sites

The way i see it leave the pcv alone and remove and block the intake side at the turbo. This actually pulls oil out ofthe head in a way. There is alot of vacuum there.

I'm aware of how that works - but wouldn't it be better to prevent as much oil vapour from entering the intake as possible? does it actually *need* to be 'drawn out' - isn't it enough to just let it breathe 'naturally'?

I'm trying to work out what the 'reason' behind leaving the PCV setup stock and allowing it to breathe into the intake manifold is...

zyeby9.jpg

This is my setup. Yes you need to draw Crank case ventilation from your engine. Believe it or not, you actually want vacuum in your crank case to help pull the ring down on to the ring land of your piston which also helps the push the ring against the bore.

Leaving the tube from your rocker cover to your turbo helps the no end.

Following the diagram, All the red lines are contaminated with oil, all the blue lines are scrubbed from vapor by baffling and steel wool in the oil air separator.

This setup is completely sealed and legal. It never needs to be drained and has 0 maintenance.

I just leave my dipstick tune in my boot and use it when necessary.

Edited by HYPED6
  • Like 1
zyeby9.jpg

This is my setup. Yes you need to draw Crank case ventilation from your engine. Believe it or not, you actually want vacuum in your crank case to help pull the ring down on to the ring land of your piston which also helps the push the ring against the bore.

Leaving the tube from your rocker cover to your turbo helps the no end.

Following the diagram, All the red lines are contaminated with oil, all the blue lines are scrubbed from vapor by baffling and steel wool in the oil air separator.

This setup is completely sealed and legal. It never needs to be drained and has 0 maintenance.

I just leave my dipstick tune in my boot and use it when necessary.

wouldnt this setup still have the same effect if used without the pcv and line? also what do you have in the catch can to stop steel wool fibres from being sucked up?

yeah thought about that.. problem is i couldn't because of the way the catch can is designed- can't open it up

i could only stuff the stainless steel wool in through the fittings

i'm using the thicker scourer type of steel wool, not the cotton look-alike soapy pad type

Edited by chiksluvit

pcv is there because what comes out the engine breathers is no good for the environment and counts as part of total emissions and the easiest way to deal with it is to burn it (cheap skate factory. well i dont blame them really )

block the pcv . no oil shit stinkin up the intake manifold

run a decent air/oil seperator baffled catch can between the rockers and turbo intake . no oil in anything systen still sealed . engine breathes fine because there is partial vacuum between the afm and

hard to jump in after the paint-master HYPED, but here goes..

I have welded a fitting onto my turbo oil drain on the block (hot-side), as setup as follows

I haven't planned on using the PCV, any problems with this setup? i haven't used it yet, the car is due to turn over in a couple of weeks.. This thread had me thinking, under boost, could i possibly be sucking oil up the oil drain and into my catchcan?? i'm guessing the turbo inlet pipe produces a vacuum but unsure to what extent..

post-30449-1291160181_thumb.jpg

wouldnt this setup still have the same effect if used without the pcv and line? also what do you have in the catch can to stop steel wool fibres from being sucked up?

Yes, if you block the PCV valve and the return line, you would just put little filters on the top of the catch can to run atmo.

hard to jump in after the paint-master HYPED, but here goes..

I have welded a fitting onto my turbo oil drain on the block (hot-side), as setup as follows

I haven't planned on using the PCV, any problems with this setup? i haven't used it yet, the car is due to turn over in a couple of weeks.. This thread had me thinking, under boost, could i possibly be sucking oil up the oil drain and into my catchcan?? i'm guessing the turbo inlet pipe produces a vacuum but unsure to what extent..

post-30449-1291160181_thumb.jpg

I'd be worried about introducing that kind of vacuum to the turbo oil return...

It would be drawing air from the crankcase via the the turbo drain.. air that would be flowing against the oil trying to drain out of the turbo (could there be enough vacuum at high rpms to pull oil up in to the can??).. the oil is not under any pressure but neither is the oil trying to flow back from the head down the factory drains (the reason why we go to these breathing extremes).. It would also mean there is a constant vacuum (fed in part by the drain) in the can which probably wouldn't help the oil to drain.

I dunno, I just wouldn't screw with it is all :)

Edited by bubba

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...