Jump to content
SAU Community

Recommended Posts

Hey All,

I jsut had an alarm put in my car and now after 10km of driving the HICAS light will come on. It will go away after a key cycle but will come up every 10km.

I have checked with the installer but he doesnt have any idea why and i have check the obvious things: fluid level and fuses both of which were fine.

I have tried to put the HICAS in diagnostic mode but it will not work.

I know HICAS has been discussed to death but it seems no one gives any answers on how to fix the problem. I do have an adverse affects when the light comes on and the steering is as usual.

If anyone can shed some light on what i should do it would be greatly appreciated.

Cheers.

remove hicas? lock bar...

mmm..probably not, i have this (probably unhealthy) obsession with keeping the car as close to origional as possible. :banana:

Would anyone on here know of someone who can diagnose the problem? im in SE suburbs in Melbourne.

have you got an aftermarket steering wheel? something has gone wrong if it wont go into diagnostic mode. Mine wouldnt do that when I had my boss kit on wrong. but the light only came on after driving over 80kmh for about 20 mins

have you got an aftermarket steering wheel? something has gone wrong if it wont go into diagnostic mode. Mine wouldnt do that when I had my boss kit on wrong. but the light only came on after driving over 80kmh for about 20 mins

nup, stock steering wheel.

I'm resetting my ecu today (letting battery run flat) with the wheels stright forward...I really dont know if it will do anything but I guess its worth a try.

check the alarm install. if in doubt revert back to stock. my guess is they have tied (or cut) a control line to the hicas box in the rear.

HICAS out, you know you want to :)

Haha, you know I love my car too much for that :D.

I've tracked the problem down to the steering angle sensor (SAS).

NOTE: I drive a 1997 S2 ECR33. I do not know if the following is true for other Skylines.

There are two signal wired coming from the sensor, one LH and one RH.

When the wheel is turned the signal will gradually change from ~5.0V to ~0V on one of the signal wires (depending if you are turning left or right).

This change in voltage tells the HICAS controller which way the wheel is turning.

If after a set distance (10km) the HICAS controller does not detect a change in signal (steering input) then it will flag an issue and go into fail-safe mode.

I have read that some people also have troubles getting the HICAS controller into diagnostic mode. If your SAS is not working then the HICAS controller will not detect you turning the wheel and will therefore not go into diag mode.

To diagnose the issue in this case, go to your boot and unplug the wiring harness from the HICAS controller. Using the below picture locate the steering angle sensor and neutral sensor pins.

post-72325-1291243746_thumb.jpg

Grab your multi meter and connect up to one of the SAS pins (21 or 22). Have someone watch the voltage change (or not change) when the steering wheel is turned. If all is working fine then the voltage should go from ~5V when steering is centred to ~0V at full lock LH or RH. Just understand that one will change when turning the wheel right and the other will change when turning left.

If the voltage remains at ~5V then most likely the SAS is stuffed. If the voltage is 0V then you most likely have an open circuit.

I hope this helps someone.

So it was deffinitly the steering angle sensor. Just has it replaced with a second hand one from the wreckers.

took the car for a nice long drive and nothing came up. Got the HICAS into diagnostic mode and all is ok.

I hope the info on here helps. Ill work on a D.I.Y. replace you steering angle sensor.

  • 2 weeks later...

So it was deffinitly the steering angle sensor. Just has it replaced with a second hand one from the wreckers.

took the car for a nice long drive and nothing came up. Got the HICAS into diagnostic mode and all is ok.

I hope the info on here helps. Ill work on a D.I.Y. replace you steering angle sensor.

please post this DIY!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...