Jump to content
SAU Community

Recommended Posts

The car you drive is unimportant and you know that - its SAU, the community.

Not just skylines!

Plus the classes for trophies (track day & S'n'S) and so on are not restricted just to skylines. Any model can win :)

  • 2 weeks later...

SAU Nationals now on Facebook - Add as a friend for stream updates as they are available :D

Username: Skylines Australia Nationals

http://www.facebook.com/settings/?tab=privacy#!/profile.php?id=100002163814442

wheres your accomodation being booked 'moid?

if one of the venues is the benalla leisure park, better make sure the owner doesnt get his knickers in a twist because the average age is below 60, doesnt drive around australia with a caravan in tow, and might make noise past 7:30pm

just sayin......me and a few mates had a run in over the weekend with him

im sure if he gets enough money coming in, he'll buy some thicker earplugs just for the weekend

Accom will be sorted/managed by a 3rd party.

There will be different prices based on whatever people want.

Details will be up - its in Shepparton and there are 10-20 places to choose from ;)

People with trailers etc are also no issue.

We are up there 4-5 times a year with SAU-Vic, the local accommodation places have no issue as long as people show respect.

Also - MORE MORE MORE adding to Facebook people.

200 people in 4 days isn't bad - but surely there is more.

It will be the primary way info will be sent out. It'll also be put onto the forum etc, however instant updates are easier ;)

A mate and i are thinking of making the trip down from Sydney, Any other Sydney boys or girls willing to make the drive down from sydney with us ?

Considering driving down from Sydney too with a mate. Should be a great weekend..

Arrival/check-in etc.

Given accomm for most places is not avail until 12pm-2pm - people simply arrive/gather.

If you convoy'd and left at like 6am, you'd be there 2-3pm no worried in perfect time.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...