Jump to content
SAU Community

Recommended Posts

Hey guys,

Well im no stranger to car car world having owned a very tough fully built R33gtst for 4 years, a 250kw evo 7 for 3 years, a wrx and Im now in a 350z

Looking at moving back into a skyline....R34 GTR. Since the cars are 10 years old now what sort of common problems have arisen over the years to look out for. I know what to look at when buying a car in general, just after specifics on the R34 GTR

Link to comment
https://www.sau.com.au/forums/topic/347438-common-problems-with-r34-gtr/
Share on other sites

GTST- Fast, fun but all over the shop and its only a gtst

Evo- A purpose built track/street weapon from the factory..add some mods and its a seriously quick car, nice car but very purposeful

350z-Absolutely beautiful car very very nice but just not quick enough.

Hard to say which one was the best, for track/mountain dutys the evo wins hands down, for the street/cruising the 350z is very sexy and super nice, for a bit of fun the gtst was great lol

Check the front CV boots before purchasing, and also front wheel bearings.

Map sensor vacuum line from the back of the plenum goes hard and splits.

Then its the usual stuff. Signs of repairs, over-spray on things that shouldnt have paint like rubbers, splitter/diffuser/undertray. Look for differences in appearance of the clear coat to spot repairs.

Then cold compression test, check for dodgy stereo wiring, modifications to the ecu wiring and any changes in the engine bay that are other than stock. Modifications are ok if done properly, but you'll spot those that arent pretty quickly.

Having someone that already owns an R34 check it out is a good idea as well, because shopping for your dream car can be overwhelming so you can have blinders on that prevent you from seeing things that others cant.

Common problems are...pedal sticking to the floor due to adrenalin addiction

Tyre wear due to awsome handling

clutch wear due to launching..haha

seriously see if you can borrow a cheap diagnostic toll (probably only $50 or so to buy and check O2 sensors, airfuel, airflow meter volts, exhaust manifold leaks and basic stuff

common problems

a. they are too expensive

b. i dont own one

a. It's never been more affordable to own an R34 GT-R than it is now.

b. Anyone can own a gtr, it's really not that hard.

From the experience I've had, they are quite a reliable and rewarding car to own and drive, albeit a bit heavy. Every car has their inherent issues. These cars are no different.

If you can, pull off the rocker cover so at least you can check the general wear and tear. A car that's serviced with regular oil changes should have a very clean head.

Coilpacks are a common problem with most r34's. They'll just die and replace them with Splitfires or equivalent.

Check the bonnet lining. Unless it's been changed in the past, it will give you an idea of how hard of a life the car's gone through.

Check for signs of panel repairs, although it's more than likely these cars have had a bingle or two due to their age. As long as repair was done properly, there shouldn't be a problem. My advice, don't get an MP II or III. They are next to impossible to colour match. The base chromium colour alone costs several hundred bucks per liter. Then you have to add the multitude of tints to get the colour right.

Give it a good launch to check the Attesa is working properly. You can check the torque split on the MFD. A good solid launch will yield almost 50% split. If it gives you a weak reading, you know there's a problem somewhere along the system and it could be costly to rectify.

Don't rely on the kms. Chances are it's wound back. Check for wear and tear on the driver side seat bolsters, gearknob, steering wheel, pedals. That will give you an idea of the real kms travelled, unless it's been changed of course.

The diffusers, especially the front can and will cop a battering when the car is lowered. Hell, even standard height they can cop some serious damage and they cost about $1500 brand new from Nissan.

Underbody rust, another common problem with these cars. Actually all imports really.

I can go on but at least it's a start for you. I'm sure there's plenty of other, more knowledgeable people here that can chime in.

Thanks for that reply mate quite helpful. Sounds like all the common problems with skylines in general being coilpacks etc etc, im luckiy that I have had a fair bit to do with both std and modified skylines in general.

I dont think i will have any worries in looking at one now, thansk guys.

My advice, don't get an MP III. They are next to impossible to colour match. The base chromium colour alone costs several hundred bucks per liter. Then you have to add the multitude of tints to get the colour right.

Is this part of your reverse-psychology marketing ploy when you're about to sell yours Eugene?

hahaaaaa.... luv it! :nyaanyaa:

  • 2 weeks later...

Yes that's a very good one. My GTT had that problem but interestingly, I haven't seen a GTR with that rust. Might need to look harder at other gtr's.

Mine has that issue on the centre boot brake light, about the size of a match head.

It's in that awkward size range where I know its there and needs to be cut out, but is small enough that i keep forgetting about it.

Brake light at the top of the boot is prone to rust.

Quite a few Japanese owners left the water sitting in the boot brake light recess, instead of going to the trouble of mopping it up.

Oh yes, when I'm a bit lazy, it can pop out of 1st.

I thought it was just stupid me, but apparently, someone else has experienced it too.

  • 1 month later...

Mine has that issue on the centre boot brake light, about the size of a match head.

It's in that awkward size range where I know its there and needs to be cut out, but is small enough that i keep forgetting about it.

Have the exact same problem with mine on the same spot. located on the left hand corner of the back tail lights, water must just sit in their.

Have the exact same problem with mine on the same spot. located on the left hand corner of the back tail lights, water must just sit in their.

Same thing on mine. I blow the water out of there every time I wash it, fair bit sits in the recess.

Gotta fix it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...