Jump to content
SAU Community

Recommended Posts

Im curious to see what these air jacks look like that SSE and Cyber were using, does anyone have pics please?

Yeah I do. Will post at some point. Only SSE's were gas powered. Cyber put little scissor jacks into the base of theirs. Very clever and cheaper but not as fast/easy to use.

for those of you who like to avoid the banter on the R35 section, here is Tarzan doing his best to battle the understeer on his hotlap. understeer was the winner on this occasion but we will be working on that for next year ;)

Found this article, worth reading regarding pro class controversies....

http://www.motoiq.com/magazine_articles/articletype/articleview/articleid/2073/world-time-attack-challenge-2011-pro-class-controversies.aspx

Handbrake - congrats on the result mate you should be proud, some more testing and the car will be a serious contender next year....

interesting info about the tyres. Looks like Berry should get his tyres out of Japan.

Bit harsh calling Glenny Alonso though.... although might be worth trying to get it to stick at the next rally event :P

lol, I guess they don't get Wilfred in Seppo land.

Interesting article, I'd like to see the equivalent from each of the other top teams. For those that haven't read it, it says "We weren't trying to hide anything, we have some trick cylinder head and run 40psi boost, and we imply but don't say that everyone else is cheating but we are clean"

How do you cheat when there are basically no rules. Other than a nitrous setup Which should be detectable to a scrutineer there are no limitations to engine mods to my knowledge.

As for tyres, if a tyre maker offerred me some secret squirrel donuts not available to the competition that would give me an edge in that department you can bet your heiny I would take them.

I'll lay london to a brick that a lot of the top compeitors have their dirty little secrets they are unwilling to share with anybody.

of course...everyone is spending big and won't want to share the results of that spend....nothing different about the top level of time attack to any other category.

their specific implications (not accusations I said) were around tyres not being purchased commercially from local supliers, and tube frame cars.

The tube frame issue is going to be an ongoing bone of contention until the promotor lays down some hard and fasts. I dont have an opinion on it either way as I know bugger all about it but it needs to be nipped in the bud before it becomes a major issue.

How long will it be before there is a major rule shakeup, what we are seeing now is a repeat of what has happenned in other forms of motor sport right from the top down. Cars became so powerful and fast it became a health hazard to drive them.

Its only a matter of time before we start seeing 1000 plus hp setups if time attack conitnues at its current rate of development.

agreed...unfortunately. Especially if they stay at Eastern Creek where power + aero will really pay off.

I don't understand the tube frame restriction at all. If you can have tube frame front and rear ends (where it really matters), allowing total freedom of suspension mounting locations and geometery, why not have a tube frame body as well? The only difference in a tube frame body would be some weight saving.

The other benefit for tube frame would be closer match to sports sedan rules (as long as they are 2wd), so these cars could be used more than once a year.

CAMS have defined a space frame chassis in the 3D regulations.

Basically A 2wd floor pan vehicle must retain, roof, pillars, door sills and the majority of the factory floor pan.

Mods to tunnels etc are permitted.

As Duncan and I have argued awd rules suck the arse ad are not worth mentioning.

A space frame Is a tube chassis which non load bearing coach work is attached.

So tube extensions are fine providing the floor pan etc remains. Can't see how the TG s14 is going to retain the oem floor pan etc.......

It's a space frame just as my R34 is too.

I dont think many of the current running cars break the "space frame" rule. But there is a few cars being built that 100% do.

The majority of the running cars are " heavy metal" sports sedans.

Which seems like a great category to now go and race a skyline!!

ok, simple. just have a seperate class for all the "tube work" modified cars. at least those of us that cant afford to hack the front and rear of our cars will have a more leval playing field.

hell im all for seeing 1000+hp cars, would be a good spectical and im half temped to do a e3 wide body now.... needs the rubber under there..

may aswell take a leaf from the 80's super silluette formula. the cars wont look much differant. all thats needed is factory roof,and doors and floor. the rest is free.

2306757754_e1bf66efb4.jpg2306744004_9510964aa7.jpg

go nuts i say. these were made in the early 80's. i rekon with todays materials and tech a s15 or gtr with a similar design using 13" wheels front a rear will put down a good time :) id pay the entry fee to go watch it :)

i didnt even attend however i did start the rumour that the food at ec is shit and would give you nitrous powered gas!

You were spot on, the food at the yuckshop was terrible

food was actually reported as being many times better than previous years. i didn't eat any though as cyber/voltex had catered lunches and kindly donated some my way. dunno where they got their food from but it was bloody good.

well yeah dagwood dog/pluto pup/corn dog is a sure fire licence to drive the porcelain bus (and yes I get sucked in and buy one now and then) but I saw people eating some burgers etc that looked pretty decent. I'd not seen that stuff before.

off the track a bit but probably the best race-track for food i've been to is fuji speedway. nice choice of options there and they serve beers too (with a cool auto beer vending machine/robot).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...