Jump to content
SAU Community

Kando Dynamics Turbo

SimonR32

By SimonR32,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Dale FZ1
Dale FZ1

My 30DET is now running TDO6H 25G, budget build with Hybrid manifold and 50mm Turbosmart gate. Turbine is the 11 blade option with 12cm housing. Tighe camshafts correctly dialled. Track car, chasin

R31Nismoid
R31Nismoid

And r33_racer or whatever also had around that figure too? Maybe it was 380? (struggling to recall)

T04GTR
T04GTR

are theese rubbish china turbos with a badge thats made in japan?

Posted Images

dori34 Grand Master

dori34

Posted
Posted

Just bought a td06 20g 10cm ext. gate for my RB , what are peoples experience with using this on the standard manifold?

Is it just a matter of putting in a 12 mm flanger spacer?

Yes and you will need extended exhaust manifold > turbo studs as well.

ran this on my old 34 made 281rwkw @ 18psi.

dyno sheet is some pages back.

if i was to do it again, i'd go high mount with t67-25g

GTScotT Grand Master

GTScotT

Posted
Posted

Don't get confused with ppl on NS. The T25 flange housings work mint, no issues. It's those ones that People had trouble with the actuators and nothing else.

the T3 housings with the 3 bolt dump pattern (internal gate off a truck) has proven to suck. Both BSA and another member tried and failed. One was an RB20 one a 25.

I know this thread is 11ty pages long but you actually need to read the thing if you hope to have an idea about the product.

Reflector Collaborator

Reflector

Posted
Posted

Hi all,

Sorry if this has been covered but after 120 pages (starting at page 1) I couldn't find what I was after and have given up on searching -_-'

Quick overview - R33 RB25det S2 Stock turbo has blown, now buying everything required to get her up and running at 300rwkw+ on 98oct BP ultimate. All the other mods I am ok with (6boost manifold, 850cc injections, greddy style intake etc...) except for two things - Wastegate and Turbo Choice.

Simons write up and numerous results have made the T67 very appealing and I see it's only being released in anti-surge now; that's not the issue though haha!

I just wanted to ask anyone with a T-67, what did you do to have the turbo only running on oil feed? Did you have to weld/close up the water supply lines from the stock turbo? Isn't it better to have a water cooled turbo to keep the oil from 'coking'?

As it is, I'm torn between these two turbos:

T-67

Or

TD06

I'm finding the TD06 more appealing as it is water cooled as well as oil fed. It also seems to have close specs to the T-67 but I couldn't seem to find any recent dyno sheets of performance results. Is it closer to or further from the performance of the T-67? Is full boost still to be expected around 4000rpm from either turbo?

As for wastegates, I have a selection that are available to me and I'm wondering what's best?

(keeping in mind this will be used in conjuction with a 6boost manifold and the target goal of 300rwkw+)

GFB EX 50mm

Or

TiAL MV-R

Or

Turbosmart Hypergate 45mm 2011+ model

Many thanks in Advanced!

Reflector Collaborator

Reflector

Posted
Posted

Thanks for the replies guys. I decided I'll probably go with a watercooled turbo which, while searching, I found this:

TD06H w/ Garrett T04R

How would this compare to the TD06SL2?

The only difference I can really find is the size of the compressor wheel and the turbine wheel. The T04R has a larger compressor wheel by 6mm and a larger turbine wheel by 6.2mm.

Would I be correct in thinking the smaller wheels on the TD06SL2 would allow the turbo to spool up slightly quicker?

Both are '400-650hp' rated so if the TD06SL2 spools quicker I'd be mad not to go for it as this will be a street build rather than track... thoughts?

Reflector Collaborator

Reflector

Posted
Posted

Go the oil cooled only T67-25g 10cm without a surge ported front cover.... Loop or block the oil lines!

Plain bearing turbo's don't need water cooling as they hold a lot more oil which is used for cooling.

Waterlines perhaps lol? Yeah I was more inclined to get the T67 but I thought retaining water cooling would be for keeping it nice and cool. I can't seem to find any that are non anti-surge that he has for sale...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...