Jump to content
SAU Community

Recommended Posts

Today i was cleaning out the boot of my r32...

and down the sides i noticed some dirt (after i pulled all the boot lining out,) and found a pair of jap sun glasses! score!!

but what i really want to know is..

there is all these scres and stuff and i noticed theres something attached to them

so i was wondering.. what electonic stuff is ment to be in the boot (on the passangers side)

Link to comment
https://www.sau.com.au/forums/topic/34940-whats-in-your-boot/
Share on other sites

The 2nd one is for the fuel pump and fuel gauge sender in the fuel tank. The cover plate gives you access to the top of the fuel tank to remove the pump & sender unit.

If you can see the ground through that one, then someone has stolen your fuel tank.

lol yeh as blind elk says thats ur fuel pump in there. if u unscrew and lift that out thats ur fuel pump. and then yeh the wiring n shit for it is connected to the top.

then the other one is where ur motor and shit are for ur power aerial which is on the outside of the car just there, as people have said. :)

in my old S13 180, it had some kind of rattley sound from the boot, i spent ages trying to fix the jack in a solid place, it still did it. stuck my arm down the side of the car in the dark and felt round (bit aprehensive to do that realy haha), and i found ... a japanese golf ball! i now it was jap coz it had jap writing on it. hehe

For sure the bottom pic is the fuel pump. The middle one would be the rubber seal. For my car, I don't hv any antenna and speaker hole at the rear at all. I know all r32 use to hv antenna in the front wind screen.

Abo Bob - You have me a bit lost on that one.. im not sure where the problem is?

Also for everyone, in that top pic where it says "Glasses" i noticed there is a metal bracket screwed in on an angel, does anyone know what this is for.. i can post pics if your not sure what i mean?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...