Jump to content
SAU Community

Recommended Posts

Cams is always an interesting debate, long argued, no real end result.

There are basically two ways of thinking.

- Larger cams, combined with a LOT of head work, oversized valves and all that $$$ jazz - works very well great power overall. You do seem to take a hit in lower RPM however.

- Smaller cams, combined with a minor tidy up - works well but gives better off/on throttle response & low RPM performance as a result.

Obviously the is about as gross of a generalisation as one can make without typing a thesis.

The bigger/flow will obviously be more efficient as RPM and perhaps make more power. Yet the smaller option will perhaps not make quite the same peak yet give you more gains on/off the loud pedal.

Depends what you are after really. Most Racepace GTR's here in Melb 2.6-2.8ltr run factory cams from what it appears. Bigger than that the advice is the 3ltr does like a little bit of larger cam love given the displacement alterations.

Syd seems a different view where everything is oversized (valves, cams, porting).

Issue is - all the results are on a dyno for both states. Now as my RB26 comparo from Racepace showed... The turbos virtually have identical boost/power graphs (-9 & -5). Yet on the street/circuit it is markedly different. It would be up to the owner to decide what they are after I guess.

Pity you weren't about over Xmas. I do intend to come up again in a month or two so I can show you the Mexican build lol.

Yeah and we all packed in the trouser department too. :nyaanyaa:

Ash are there any of the examples using OS valves at Racepace or do they prefer using stock sized valves.

Rightio. Another cheeky question.

Would a 90 mm exhaust from the front pipes back (twin 3 inch into a single 90 outlet) be big enough.... or do we "really" need a 4 inch.

3.5 inch (90 mm.. close enough) vs a 4 inch (101.6mm)

Rightio. Another cheeky question.

Would a 90 mm exhaust from the front pipes back (twin 3 inch into a single 90 outlet) be big enough.... or do we "really" need a 4 inch.

3.5 inch (90 mm.. close enough) vs a 4 inch (101.6mm)

I'd say the 4 inch exhaust will benefit throughout the rev range.

It's just trying to keep the sucker quiet!!!

Tangomatt has a 4 inch cat back exhaust with custom Racepace mufflers, quiet on idle but oh the sound at high rpm!!!!!

Paul - 4" mate for 400rwkw.

3.5" for 350

and 3" for 300

See a theme? :D

Yeah and we all packed in the trouser department too. :nyaanyaa:

Ash are there any of the examples using OS valves at Racepace or do they prefer using stock sized valves.

Stock is the common choice :)

yeah but 4" exhaust and 10.8mm lift cams sounds awesome :thumbsup: ... love it when the whole car shakes at idle hehehe... even though its bottom end and mid-range sucks compared to most of the other Racepace cars... but that's more to do with the truck turbos than anything else

oh well nearly time to run E85, up the boost and see if I can't break the turbos so I can change to -5 :pirate:

yeah but 4" exhaust and 10.8mm lift cams sounds awesome :thumbsup: ... love it when the whole car shakes at idle hehehe... even though its bottom end and mid-range sucks compared to most of the other Racepace cars... but that's more to do with the truck turbos than anything else

oh well nearly time to run E85, up the boost and see if I can't break the turbos so I can change to -5 :pirate:

I like it when I'm at the lights and everyone gives me a dirty look and winds up their windows hehe.

yep... with the uprated springs, retainers and lifters... a credit to racepace tuning it actually runs really smoothly, just a lope at idle... I think if you are going to upgrade cams go for as much lift and as little overlap as possible... so you get the most torque benefit you can without moving the powerband up too much

yep... with the uprated springs, retainers and lifters... a credit to racepace tuning it actually runs really smoothly, just a lope at idle... I think if you are going to upgrade cams go for as much lift and as little overlap as possible... so you get the most torque benefit you can without moving the powerband up too much

Well I have 270's @ 10.25 so more duration and less lift. I only rev mine to 8 - 8.5 so i could get away with the 260's...

Ive noticed how big overlap cams bring boost on sooner with turbo cars, this is no doubt due to the extra exhaust energy being delivered to the turbo instead of crank.

Could a similar thing be achieved with stock cams, just retard the ignition when coming onto boost, whether or not the extra torque the boost gives cancels out the lack of power from the ignition I can't imagine it'd be any different from just running big cams. You would only need to do it from say 1500-2500 rpm to get it spooling a little earlier.

What do people think?

I found this out due to a bug with my nistune ecu where occasionally the cold start map would shit itself and put max retard on the timing. Could get 4psi in neutral and it would make the stock turbo surge like crazy at 2000rpm due to it building 10psi with the throttle barely cracked open. Made the car undrivable as it was so doughy but so much boost that it would kick back and forth from no power to loads of power as it came out of the map.

How much difference does that Vcam make?

A lot !!

Standard idle feeling, boost on quicker and at lower rpm.

Can run laggy turbo / turbo's setup and lose the lag.

Its a shame theres not more being used in Oz.

Driven this setup a few times now and its response and power is bloody awesome.

6af5e5eb.jpg

b664f4a2.jpg

8506ea1c.jpg

7e792031.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...