Jump to content
SAU Community

Recommended Posts

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Will 18 x 9.5 +30 fit ok?

I know the GTR rims fit fine and they are 9.0 +30....

Dont want to buy rims that dont fit...again!

I would stick to 9 inch +30, mine stuck out a little on the front and were nearly rubbing on the inside but they are 17's.

I must admit, it makes the car handle the corners well with the 9 inch rims with semi's but the refinement I have now with the 8 inch + 235 road tyres makes up for it. No hint of tramlining or noise, good grip, its only the softer sidewalls causing it to feel a bit squirmy turning a tight radius corner.

Can anyone vouch for the accuracy of this site?

http://www.rimsntires.com/rt_specs.jsp

Apparently if I go 245/45/18 x 9.5 +30 it'll be the same (clearance wise) as my stock 215/55/17 x 7 +45 setup...and it'll stick out 30mm

Edited by ironpaw
  • 2 weeks later...

please clarify

i have been told from numerouse mag wheel dealers that 9.5 on the stagea is to wide and will creat issues

i am looking at dropping my m35 on some BC BR coilovers and running big break kits witch mean ill be running 19 inch mags

so what size width mags can i get with 19s? that i can use on the stagea that wont rub 8.5s or 9s

if i get a spacer does that mean i can go wider ?

with offset does a - or a + offset mean a bigger dish etc

or do u guys recomend 18s for the stagea

please clarify

i have been told from numerouse mag wheel dealers that 9.5 on the stagea is to wide and will creat issues

i am looking at dropping my m35 on some BC BR coilovers and running big break kits witch mean ill be running 19 inch mags

so what size width mags can i get with 19s? that i can use on the stagea that wont rub 8.5s or 9s

if i get a spacer does that mean i can go wider ?

with offset does a - or a + offset mean a bigger dish etc

or do u guys recomend 18s for the stagea

Spoolin12 , is running 19x9.5 at what must be around+20 odd now. At +30 his were still under the guards... Just. The tops tuck in more the lower you go.

He'd be the man to talk to, as I think his rims are probably the widest and the most aggressive offsets on here.

+ or - doesn't mean anything with regard to dish; only offset. However, the closer to a -ve offset you go; the better chance of dish.

Spoolin12 , is running 19x9.5 at what must be around+20 odd now. At +30 his were still under the guards... Just. The tops tuck in more the lower you go.

He'd be the man to talk to, as I think his rims are probably the widest and the most aggressive offsets on here.

+ or - doesn't mean anything with regard to dish; only offset. However, the closer to a -ve offset you go; the better chance of dish.

He told me he was running +40's? so he must've been running a 10mm spacer...

Guess my 9.5 +12 LE37's ain't gonna fit without guards being rolled!

What brand/model rims did Spoolin run?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...