Jump to content
SAU Community

Recommended Posts

hai guise, was wondering if there are any home tricks to checking the state of the intake? IE if there are any air leaks?

or do i need to take the car to a shop for them to pressure test it?

cheers

Edited by Clutch
Link to comment
https://www.sau.com.au/forums/topic/351535-intake-leak-test/
Share on other sites

I made up a cheap one with some pvc pipe caps and a $20 hand pump. See below photos. I blocked off the pipe going into the throttle body, hooked up the pump to where the pod filter was and pumped away.

The advantage of the hand pump over an air compressor is that because it is quiet it is very easy to hear even the smallest leak.

Do you mean the intake manifold or intake piping? Mine was for the intake piping.

post-29432-0-01090900-1295839930_thumb.jpg

post-29432-0-80208500-1295839934_thumb.jpg

post-29432-0-91684800-1295839940_thumb.jpg

If you get a can of Aerostart or similar and spray it around while the car is idling it should raise the revs if theres a leak as it will suck it in. Perhaps not as good as the method mentioned above but if your looking to do it without spending to much that would be the the way to go

To check for a leak in intercooler, piping or around silicon joins, etc spray with soapy water, preferably while at a high idle (1500-2000rpm is plenty).

If you have a leak it will blow bubbles.

Seems wierd & you may think the water would get sucked in but it works...

Another good one is to remove your pod / airbox so you have access to the afm and while the car is idling cover the afm with your hand so no air can get in.

Then you should be able to hear the hiss of where the air is getting into the intake.

if you have a leak as well, you should blow a small amount of black smoke on boost. some of the air will escape the intake piping, but since it's still being measured by the AFM the correct amount of fuel will be going in as though there wasn't a leak.

Unless you're running a MAP sensor like me. then you're screwed for this idea lol

yes. If the leak is big enough in your case, you'll be sucking in air that hasn't been measures by the AFM while idling or off-boost. This will cause you to run lean, and missfire like a 14yr old boy at a wet T-shirt comp.

Damn you!

I read this thread a couple of hours ago and thought hmmm maybe i'll go look over my intake to see if I have any leaks. Turns out I have a leak coming from under the plenum where the damn gasket has slightly blown out.

God damnit!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...