Jump to content
SAU Community

Recommended Posts

I bought a brand new gt3071r from some guy who was meant to put it on his car but ended up using something else. Anyway, by my own fault, I assumed it was a t3 gt3071r as I was under the impression all gt30 turbos(well majority) are t3. This one though is a t2.

Could I run a t2 to t3 adapter? Its a .86 rear and the front is .50 or some shit.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/352190-gt3071r-is-this-bad/
Share on other sites

I think room will be fine. I just need this clarified.

Is the ONLY difference between a T2 .86 and a T3 .86 the flange? Is the housing the same size? Will the flange size be restrictive or will it open up inside the housing to allow the same flow of exhaust as a T3 just be abit tighter up front? I don't want to hit 5krpm then watch a downhill decent...

they have a different turbine. In general; cropped gt30 in the t2 housings vs uncropped gt30 in the t3 housings.

Though the .86 t2 sized housing is roughly equivalent to a .63 t3. OK for a 3071 on an rb25 though the internal waste gate size may be marginal.

I was considering trying this exact turbo. Could be a cheap way to get near GTRS performance on an RB25. I would expect it would be slightly restricted by the smaller flange but it depends on your power goals. GTRS (2871) don't make all that much power anyway. A full turbine 3071 will give more top end but at the expense of response. Some would say you might as well go 3076.

No they do both 84 and 90 trim turbine versions . Turbo number 700382-3 using cartridge number 700177-3 has the 84 trim turbine where unit 700382-20 with cartridge 700177-4 uses the 90 trim turbine variant .

Also all the so called HKS GT2835 variants use the T2/25/28 flange size except the Pro S ones which are T3 footprint .

I think the easiest turbine housing solution would be for Garrett to machine their GT30 IW ones to match these cropped turbines , a cropped GT30 turbine would work better in a GT30 turbine housing than GT28 ones IMO .

A .

Yeah I didn't be more specific before. The 90 trim TURBO part number is .86 but has a housing option for .64 and the TURBO part number for the 84 trim is .64 but has a .86 housing option. I assumed the turbo is just an off the shelf Garrett part. My bad.

Ah shit forgot about HKS T2 flanges

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...