Jump to content
SAU Community

Recommended Posts

Hi Nick,

This motor build will have both with minimum lag or no lag so response under full boost and response in boost. The boost we are looking at running is 64psi absolute on the turbo side and that should equate out about 34psi gauge before the throttle bodies, remember this is all calculated, we will be follwoing the laws of Joule thomson effects.

You must all have a read of the below link now you know why people run big boost rememebr when the F1 where turbo they used to run 5bar boost.

http://en.wikipedia.org/wiki/Joule%E2%80%93Thomson_effect

thanks, should be a real animal with that much boost + revs :worship: ... that link is a bit over my head but I'm trying

those 80's F1 engines are ridiculous, but plenty of lag there;)

I guess we shouldn't complain too much, the old Sierra Cosworths were much bigger p1gs than our GTRs

I guess the modification to your quench pads will help you run such a high static compression ratio with quite a substantial amount of boost.

What fuel will you be using, I think I missed this further back ?

I guess the modification to your quench pads will help you run such a high static compression ratio with quite a substantial amount of boost.

What fuel will you be using, I think I missed this further back ?

The squish area has not ben touched however the clearance has been changed by closing the gap further then standard.

The car will be tuned on E85 caltex.

Below is a pic showing how the wastegate will merge into the dump pipe and act like a venturi to help remove gases from the turbine.

Also there will be an addition of a fitting fitted at the bottom of the manifold collector, that can be connected to compressed air on board and spray it in for boost at idle, a good ay to launch of the mark. I know this is all new to alot of people as its all new to me, will have to see how it all works.

post-49633-0-60966800-1301992447_thumb.jpg

I will make sure i get detailed pic of the merge i hope people can copy this method and use it to there benefit

How did you form it? I'm also impressed with the manifold merge collector. I like to see people trying new things (well old theory, but not common ground). Keep up the great work.

How did you form it? I'm also impressed with the manifold merge collector. I like to see people trying new things (well old theory, but not common ground). Keep up the great work.

Here are some old pics on how the collector was made, it took 100hrs to make

Design started from this

post-49633-0-57143800-1302007791_thumb.jpg

post-49633-0-42330700-1302008027_thumb.jpg

A wooden template was made first to see if it would work

post-49633-0-13381700-1302007248_thumb.jpg

Made from billet 321 stainless

post-49633-0-41043200-1302007410_thumb.jpg

post-49633-0-93361500-1302007530_thumb.jpg

post-49633-0-98927600-1302007626_thumb.jpg

I'm pretty eager to see how the dump will terminate, because at the moment it has the makings of the best possible solution for exhausting the gases.

The interesting part will be the packaging, unless your planning on running a side pipe :P

Very very nice fabrication work.

I'm pretty eager to see how the dump will terminate, because at the moment it has the makings of the best possible solution for exhausting the gases.

The interesting part will be the packaging, unless your planning on running a side pipe :P

Very very nice fabrication work.

Thank you the fab work is not easy.

Will be running a full exhaust this car will comply to RTA road rules and comply with emmisions also

Below is a pic showing how the wastegate will merge into the dump pipe and act like a venturi to help remove gases from the turbine.

Hi Bobby, can you update with photos to show how this will work?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...