Jump to content
SAU Community

Recommended Posts

im thinking of getting my 32 diff welded so its always locked and its my daily but is all the storys true that it can snap. knocking noise when taking full lock turn. ?

or to get a 2 way which is hard to find in 6 bolts ?

Link to comment
https://www.sau.com.au/forums/topic/355620-to-get-my-diff-welded-or-get-2way/
Share on other sites

If it's your daily and you're worried about all that stuff, then just shim up your stocker.

Or..

Don't be a pussy. My 32 was daily driven with a button clutch and 2-way for a couple of years.. good times :ermm:

Try driving an N/A, RWD, 1 tonner V6 Rodeo.

That thing comes with a locked diff as standard, chirps out something mean and is an utter death trap in the wet! In the dry though that thing is awesome fun.

I'd say your mild manned N/A would be safe with a cheap weld!

Try driving an N/A, RWD, 1 tonner V6 Rodeo.

That thing comes with a locked diff as standard, chirps out something mean and is an utter death trap in the wet! In the dry though that thing is awesome fun.

I'd say your mild manned N/A would be safe with a cheap weld!

i assume you mean to say it has a factory fittled LSD.

Locked diffs are illegal for street use, so i highly doubt your car has a factory locker. (reason being, they promote understeer when small throttle inputs only are applied.)

Imagine that nanna jenny gets in her hubby ute... she goes down to the shops but being elderly and irratic in her driving she comes straight off the throttle and turns hard and late at the first corner she gets to... now if there is no throttle then how is the inside wheel going to break traction to spin at constant speed with the outside wheel when turning.... it wont. it will want to push the car in a staright line.... see what im getting at.

this wont be the case in all chassis or road conditions. both my 33s have had locked differential and i have not had those problems but in other chassis it is a problem.

But it may well be a very tight lsd. Most decent four wheel drives and utes come standard with or are available with a farely heavy duty lsd.

  • Like 1

i assume you mean to say it has a factory fittled LSD.

Locked diffs are illegal for street use, so i highly doubt your car has a factory locker. (reason being, they promote understeer when small throttle inputs only are applied.)

Imagine that nanna jenny gets in her hubby ute... she goes down to the shops but being elderly and irratic in her driving she comes straight off the throttle and turns hard and late at the first corner she gets to... now if there is no throttle then how is the inside wheel going to break traction to spin at constant speed with the outside wheel when turning.... it wont. it will want to push the car in a staright line.... see what im getting at.

this wont be the case in all chassis or road conditions. both my 33s have had locked differential and i have not had those problems but in other chassis it is a problem.

But it may well be a very tight lsd. Most decent four wheel drives and utes come standard with or are available with a farely heavy duty lsd.

+1

definitely heavy duty lsd then haha

yup. and its sooo much better than having a 1 tonner with an open center...they see a hill or some grass and just cock a leg and go nooo where.

yer of corse. many cars would be useless without lsd but from factory the lsds start to lock up upon acceleration.... not deacceleration.

track cars... yer grab a 2way lsd or a locker. in a drift car its good for obvious reasons and in a circuit car you usually getting ready to get back on the power by the time ur at the apex. also there generally isnt trees or power poles at a race track lol and u have better rubber on the car so the front has half a chance at fighting understeer. (but better rubber at the back can also increase its tendancy to 'drive straight' if rear is locked.)

by 6 bolt does it have 6x1 or 3x2 pattern?

cheers everyone.

thats very unlucky for ur mate.

yes its 3x2 .

and so what if its non turbo big deal your car might beat me on a straight but "Men with guts attack those corners!"

yeah just checked mates his welded diff has been fine.

because a 1.5 way is not predictable to a 2way or, welded always predictable.

  • Nope 1

yer of corse. many cars would be useless without lsd but from factory the lsds start to lock up upon acceleration.... not deacceleration.

track cars... yer grab a 2way lsd or a locker. in a drift car its good for obvious reasons and in a circuit car you usually getting ready to get back on the power by the time ur at the apex. also there generally isnt trees or power poles at a race track lol and u have better rubber on the car so the front has half a chance at fighting understeer. (but better rubber at the back can also increase its tendancy to 'drive straight' if rear is locked.)

A 2 way (even a tight 1.5 way) will push the car into understeer. A locked diff is worse. Much worse.

and so what if its non turbo big deal your car might beat me on a straight but "Men with guts attack those corners!"

yeah just checked mates his welded diff has been fine.

because a 1.5 way is not predictable to a 2way or, welded always predictable.

That is nonsense A 1.5 way is as predictable as a 2 way. It also allows the car to handle a whole lot bettr because the diff doesn't have the same propensity to lock on the over run.

Bottom line: dont run a welded diff on a road car. Not only is it illegal, it is dangerous.

Edited by djr81
  • Nope 1

honestly, i have had a car with a welded diff, and i have driven a number of other with them, and i never had a problem with it on the streets )apart from the skipping noise when doing a tight turn around cops ;))

i do however agree that a propper 1.5 or 2 way is 100 times better, but i'd rather have a weldy than a single pegger!

as long as you are aware of it, then there should be a danger, just dont give the car to the mrs ;)

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...