Jump to content
SAU Community

Recommended Posts

more progress.

its getting abit tight on the rh side with the intercooler and pump and the oil filter block

DSC_0326.JPG

imageproxy.php?img=&key=4b1e78680f916b86

DSC_0327.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

intercooler water pipes are 1 1/4". just dummied up for now so i could see where i could fit the pump. (ewp130)

the engine bay is almost complete except wiring and cooler pipes

DSC_0332.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

DSC_0333.JPGi used 2 w201 merc radiator welded together for the interooler heat exchanger. the are perhaps a little two tall. but still fit. i got a great deal on them. must of smudged the camera lens..

DSC_0334.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

Modena engineering sequential oil filter all plumbedDSC_0329.JPG

Ford cobra svt 8.8 irs conversion in the rear with a 31 spline wavetrac lsd using 2 stock axles 4" 316L exhaust. waiting on the muffler. 110liter fuel tank with 2 walbro 400's in a separate pot in the tank.

DSC_0331.JPGstill have lots of wiring to do. but shouldnt be to much longer as ive done most of the mechanical stuff.

DSC_0328.JPG

  • Like 3

more progress.

its getting abit tight on the rh side with the intercooler and pump and the oil filter block

DSC_0326.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSC_0327.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

intercooler water pipes are 1 1/4". just dummied up for now so i could see where i could fit the pump. (ewp130)

the engine bay is almost complete except wiring and cooler pipes

DSC_0332.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSC_0333.JPG

i used 2 w201 merc radiator welded together for the interooler heat exchanger. the are perhaps a little two tall. but still fit. i got a great deal on them. must of smudged the camera lens..

DSC_0334.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Modena engineering sequential oil filter all plumbed

DSC_0329.JPG

Ford cobra svt 8.8 irs conversion in the rear with a 31 spline wavetrac lsd using 2 stock axles 4" 316L exhaust. waiting on the muffler. 110liter fuel tank with 2 walbro 400's in a separate pot in the tank.

 

DSC_0331.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

still have lots of wiring to do. but shouldnt be to much longer as ive done most of the mechanical stuff.

DSC_0328.JPG

  • Like 2
  • 4 months later...

getting pretty close now. just wiring and some more fab on the intercoolers.

i read the wiring diagram wrong, and wired all the crank and cam sensors up backwards. killed all of them, so at $115 each i needed a better solution. so i picked the popular cherry gear tooth hall sensors, and turns out that a standard a/c pipe pad mount has the same dimensions as the sensors. :)

DSC_0373.thumb.JPG.617aa9f5ea8c77c2dfbf9cba33e37fde.JPGDSC_0372.JPG.5a716e1c0297833a2a906839977ff59f.JPG

 

the engine a gearbox ready for the 100th and final fit.engine.thumb.jpg.7d103ab14704767d5e7777cce9a64013.jpgengine1.thumb.jpg.5ddbff99560fa2142cdf0db0d4af1c42.jpg

 

 

  • Like 11

made an auxiliary air tank for the paddle shift out of an old extinguisher. since the compressor and tank is in the boot. i didn't want any losses in the air pipes. has a short run of 3/8 tubing to the valve bock.

also an under body photo showing how cramped it is!

underbody.jpg

airtank.jpg

  • Like 3
  • 3 weeks later...

well... it starts!! :) some wierd settings in a sub menu were stopping the engine from starting. video up soon. big thanks to Ryan from SYVECS. what took me over a week to work out he did in about 10 seconds over team viewer. (from Dubai)

even on methanol it seems pretty good.  now ive got to button up the body loom and put the interior and dash in it. yays

  • Like 7
  • 2 months later...

sorry for the lack of updates. had some small issues.

gearbox linkage had to be redone after i got the paddle shift working. had to send the ecu back to the uk to fix the 5v output that i blew by reverse polarity (dt 12way connectors can go both ways... :( send battery power to 5v outs and into the can1 output

also the superfan worked to well. it was cooling the water so much it was closing the thermostat, the then overheating. so i put on a "coolant in" temp sensor. and the fan is controlled via a custom 3d table via pwm.  works really well now. and coolant stays within 2 degc idling or on the 2 step :)

running e85 now. 

things left to do. :

a/c hoses

brake fluid reservoirs

inner guard liners

cal switches

get a new efr boost solinoid (snapped the leg off one...)

some kind of gear boot(not stopping it from driving)

sort out some small issues with the dash (plex sdm700) more like i need to learn more about can communications.. (im kind of proficient with it now, but still not up to speed 100%)

put the seats and console back in.

get 2 ntk l2h2 lambda sensors that are the same.. (left bank runs abit richer showing the same lambda) egt tells the story

 

so not heaps, just little bits and pieces.

ps, what color should i powder-coat the inlet manifolds?

 

 

                               

  • Like 4
  • 3 weeks later...

seem to be stuck with a vct rattle.

ordered new Teflon vct seals and solenoids.  the intake cams rattle at 3000rpm ish with no power to vct solenoids. put some advance in it and it gets louder... farken..

pulled timing cover off to see if i have a blown oil gallery gasket, all ok. o rings ok. has new vct gears.

has poncams and jwt springs so i cant see that as being to much for the gears.. timing chains are all mint. (engine had low k's on it when i bought it)

seems to have a oil pressure issue to the gears. nowhere to measure the pressure applied either.. but the cam angle is achieved almost instantly, so the gears work and oil pressure is there.

cant see it being the gears, as they are the latest spec and have 0 km on them.  il have to wait till the parts come in to see if that fixes it.

going to tune it up anyway.

  • Like 1
  • 2 weeks later...

just took it for a lap around the block with a r35gtr 1000cc injector basemap

700kpa boost in 3rd bakes them.. perhaps the tyres have gone hard comes on boost pretty early. 3k ish

things to fix.

front wheel speed (for traction control)

need to adjust the pedal to throttle ratio to make it smoother

needs more tuning for the paddle shift

needs some sound deadner for the tunnel. (gearbox is pretty loud)

gas up a/c

dyno tune

need to learn how to drive again....

wait for a firmware patch to fix the farkn dash. (display freezes up if rpm is connected to it.....)

 

 

 

  • Like 6

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...