Jump to content
SAU Community

Recommended Posts

Hi Guys,

i know there is a lot of questions regarding offsets and wheel sizes for skylines, but i'm a newbie and haven't found any r33 gtst with the dimensions below

18x8" offset +40 front

18x9" offset +40 rear

my car is lowered 30mm with king springs, will they fit and will i have to do anything to the guards??

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/356123-wheel-offset-for-r33-gtst/
Share on other sites

....It will look fine

But If you wanna be one of these guys that spend a fortune to get the flush look, even though it provides no great performance benefits,then go for it.

EDIT..i do hope your not running standard shocks with those springs..If not you should spend your money on some good quality shocks before worrying about different wheel offsets.

need wider dude....

+40 will look like a bag of dicks

how do you know what a bag of dicks looks like??

Arent you meant o be on some cruise anyway.. :P

It may not look the greatest but it will still look better than most and i think a good quality set of shocks should be of higher priority if they are not done already..Crappy shocks with hard springs and no tyre sidewall = a pretty crappy and unsafe ride

Why put all this pressure on these kids to make their car look a certain way then grumble when they get pulled over and defected because they spend more money trying to look cool rather than actually enhancing their vehicles performance.

EDIT anyway if your that concerned just stick some spacers on them..

....It will look fine

But If you wanna be one of these guys that spend a fortune to get the flush look, even though it provides no great performance benefits,then go for it.

EDIT..i do hope your not running standard shocks with those springs..If not you should spend your money on some good quality shocks before worrying about different wheel offsets.

What fortune is needed to get the flush look?

post-76142-0-48569300-1299400993_thumb.jpg

i know there is no real standard as everyone like different looks and stuff but thats nice i think.... lol no spacers

and only $850 a few weeks ago on here with tyres..

but as Arthur T3 said just stick spacers in your ones...

Thanks for the feedback guys.. I have replaced the king springs with Tein coilovers just today and the wheel dimensions I put on earlier were for a set of bbs lm replicas.. Does any1 know where I can get a set of lm replicas that will sit more flush?

VarrsToen in the US make BBS LM reps, but they will sit more poke than flush without rolling/flaring/pumping (19x9.5/10.5+0)

18x9+32 all round. Ran fine without modifying the guards. Only time I got scrapage was on bumpy corners...but a guard roll fixed that, and it's completely related to how low/high your car is. But yeah, as Hamish said...you'll be unhappy with the looks after a while, if you don't get offset and width right straight up. Mine look okay, but I'm now trading my rears for 9.5...will make things look even better without the need for guard flaring.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...