Jump to content
SAU Community

Recommended Posts

Haha no not retreads.

Fair enough if you have spent the dollars on a new setup...what are they???? :)

Weds SA90 :)

They just off getting some colour change love!

And Snowys old Tien's to go in as well.

  • Replies 136
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

LOTS of dish with the offset I have (there is a pic on my FB mobile uploads if you wanna see from a couple months ago) :)

I hate TE37's TBH. Every one has them! Took 8-9 months to find a set of SA90's (Via everyone friend @ Import Monster). Was looking for them before i even owned a GTR lol.

First track day for me, is a MotoX style helmet ok? also anything else I need to make sure to bring? so I don't miss out after a 2.5 hour drive :P

Can I renew cams license on the day?

-Leigh

First track day for me, is a MotoX style helmet ok? also anything else I need to make sure to bring? so I don't miss out after a 2.5 hour drive :P

Can I renew cams license on the day?

-Leigh

moto helmet is fine. Wipe the mud off first :)

Bring extra pads, brake fluid, oil, tools, jack, fire extiguisher mounted well!

Jerry can of fuel. You'll prob go through more than half a tank.

Can't do cams at winton I don't think.

moto helmet is fine. Wipe the mud off first :)

Bring extra pads, brake fluid, oil, tools, jack, fire extiguisher mounted well!

Jerry can of fuel. You'll prob go through more than half a tank.

Can't do cams at winton I don't think.

Thanks for the quick reply :thumbsup: will try and organize all this.

Should I be overfilling my engine a bit with oil? (only just had 100k service at racepace so most things should be ok)

Can anyone tell me more info about renewing CAMS?

You may have left it late to renew CAMS, it generally takes 10 days to fully process. You won't be able to renew on the day, though check with wrx club. [email protected]

Prob have to sign up for AASA if you can't get CAMS through...You can do that at Winton. Or drop into CAMS in caulfield? Though that may cost extra $$$.

The motoX helmet will need AS1698 or greater sticker on it (SNELL or FIA as well).

You may have left it late to renew CAMS, it generally takes 10 days to fully process. You won't be able to renew on the day, though check with wrx club. [email protected]

If you want cams and have time go into their office in malvern (i think it's malvern)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...