Jump to content
SAU Community

Recommended Posts

do i have to do that whole thing or just the first part ???

"How to reset your ECU and perform the Throttle Pedal Release and Idle Air Volume Learning procedures on an Nissan 350Z.

Before attempting any of the following procedures, it is advisable that you read through the instructions thoroughly and familiarize yourself with them.

A stop watch or an analog clock with a second’s needle will be useful.

**a quick reset can be accomplished by disconnecting the negative battery terminal, and depressing the brake a few times.

ECU Resetting procedures

Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON.

Operations procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.

2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.

2a. Fully depress the accelerator pedal (HARD).

2b. Fully release the accelerator pedal.

3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.

4. Fully release the accelerator pedal (while the CEL is still blinking)

5. Wait about 10 second.

6. Fully depress the accelerator pedal and keep it for more than 10 seconds.

7. Fully release the accelerator pedal (The CEL light will continue to blink).

8. Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone.

If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to Resetting the ECU.

Accelerator Pedal Release Position Learning

Operation Procedure

1. Make sure that the accelerator pedal is fully released.

2. Turn ignition switch “ON” and wait at least 2 seconds.

3. Turn ignition switch “OFF” wait at least 10 seconds.

4. Turn ignition switch “ON” and wait at least 2 seconds.

5. Turn ignition switch “OFF” wait at least 10 seconds.

Throttle Valve Closed Position Learning

Operation procedures

1. Make sure that accelerator pedal is fully released.

2. Turn ignition switch to “ON”.

3. Turn ignition switch to “OFF” wait at least 10 seconds.

Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.

Idle Air Volume Learning (Throttle Position Learning)

It is better to count the time accurately with a clock. 1. Perform “Accelerator Pedal Released Position Learning”.

2. Perform “Throttle Valve Closed Position Learning”.

3. Start engine and warm it up to normal operating temperature.

4. Turn ignition switch “OFF” and wait at least 10 seconds.

5. Confirm that the accelerator pedal is fully released, then turn ignition switch “ON” and wait 3 seconds.

6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.

7a. Fully depress the accelerator pedal (HARD)

7b. Fully release the accelerator pedal.

8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.

9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.

10. Start engine and let it idle.

11. Wait 20 seconds.

12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications. "

im assuming to change the front headlight globes u have to pull out the whole airbox to get to the pasengers side and probly just the overflow bottle on the drivers side or is there an easier way ???

:cheers:

youll need the guard linings out to change the parkers. well, i did. to change the burners, just airbox and overflow bottle as you already said

just remember DO NOT touch the glass of the burner (the HID globe) if you do, get some contact spray and clean it off

youll need the guard linings out to change the parkers. well, i did. to change the burners, just airbox and overflow bottle as you already said

just remember DO NOT touch the glass of the burner (the HID globe) if you do, get some contact spray and clean it off

+1 when I first did this as a noob, the globe died within a week or something..

yup you did hahaha

in at jaycar they have HID retro kits now for $60 or $70. same as my cheap asian crap i got for $120 last year.

its costing me 180 to get a genuine loom and ballast etc from japan. lucky i had most of a car to get the other headlight from lol

but i like the blue hue.. lol mine are 8000k(dont flame)

i can see well enough, especially with the other lights there anyway.

nothing wrong with 6000k.....got my globes from japan delivered for $94.....2 years no prob's!

youll need the guard linings out to change the parkers. well, i did. to change the burners, just airbox and overflow bottle as you already said

just remember DO NOT touch the glass of the burner (the HID globe) if you do, get some contact spray and clean it off

ahhh sweet thats what i needed to know cos im just changing the parkers to match the Xenons :banana:

yep the sweat/grease off your hands wreck any halogen type globe just whipe them with metho and they'll be sweet!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...