Jump to content
SAU Community

Recommended Posts

Hi there,

I have an R33GTST and apart from the high flowed units I was wondering which other 'out of the box' units would fit?

I have not a lot of experience with turbo installation, but what I got so far is that there are quite a few

T3-Flange Units out there.

For example this one:

3076R

This turbo has many options, but the 6 bolt mount for my Nissan is not listed. :(

So in reality how are these Turbos matched to the existing piping?

Would it be an option to get a used turbo elbow and then weld / machine some kind of adapter?

Or are these adapters available somewhere?

Many thanks ...

Edited by Torques
  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

The honest easiest way is definitely a highflow, as stated above.

We would have no idea about your options in the UK, yet if you are not after a very specific setup you should just decide how much power you want, or how fast you want to go, then pick your turbo to suit.

For example if you were in aus and wanted sub 300rwkw with as little as hassle as possible you would simply buy a hypergear G2 or G3 turbo for 260 or 300rwkw respectively. Obviously these would net the results and save you alot of cash, spending the VAST amount more would net you the same result with a better outcome overall.

Overall implying drivability, spool etc.

Ideally you would want a forward facing plenum, otherwise the standard pipes get in the way of the 4" intake on the 3076 and it just looks messy in my opinion.

But these guys offer a 6 bolt rear housing :thumbsup:

http://www.horsepowe...IAB2/prod18.htm

Just seen that your in the UK, but there are places that do give the option so there might be one there if you ask around

Ideally you would want a forward facing plenum, otherwise the standard pipes get in the way of the 4" intake on the 3076 and it just looks messy in my opinion.

But these guys offer a 6 bolt rear housing :thumbsup:

http://www.horsepowe...IAB2/prod18.htm

Yeah I was originally going to get the 3076r with the 6 bolt rear on the stock manifold but I'm glad I went the whole hog in the end with the high mount exhaust manifold and forward facing plenum. It's about a trillion times sexier and didn't cost that much more.

_1019404Medium.jpg

Hello to OZ,

Thanks for the replies ..

I would be very happy with 300RWKW, and fancy fat torque over peak power.

Also I would like quick response (so 12PSI+ @3000rpm).

If I could find a used R34GTT turbine, it would be a good bases to high flow it using

a different turbo cartidge.

Cheers ...

I would be very happy with 300RWKW, and fancy fat torque over peak power.

Also I would like quick response (so 12PSI+ @3000rpm).

Specifically, 12psi @ 3000rpm with 300rwkw to boot is a tall order.

3000rpm is next to nothing and at those revs with that boost this turbo will still be feeling lethargic. Try to grasp that boost @ rpm wont = power nor response, so planning where you want to hit 12psi is next to useless. What you do want to plan is at what RPM you start making good power.

The general consensus for good response is 200rwkw @ 4000rpm. It is a slightly tall order from a 3076r in a reasonable cost effective setup, you will see most making the 140-180 mark. That sort of power and response can be experienced through a highflow, yet the torque and overall feel of the turbo will suffer.

I think you will keep being referred back to the highflow option more than anything else, yet make sure you pick a builder who has well documented results.

Hello,

Yes ... you are correct, high boost at low RPM and 300kw at the rear is probably asking for too much and maybe not possible with a single turbo.

But 200kw at 4000rpm sounds quite good to me.

And 2500-4500 is the range I use the engine most of the time..

I was told a recore with the 3076 internals would be something to consider.

The thing is that a high flowed turbo is not any cheaper compared to

an off the shelf unit.

Many thanks ...

Specifically, 12psi @ 3000rpm with 300rwkw to boot is a tall order.

3000rpm is next to nothing and at those revs with that boost this turbo will still be feeling lethargic. Try to grasp that boost @ rpm wont = power nor response, so planning where you want to hit 12psi is next to useless. What you do want to plan is at what RPM you start making good power.

The general consensus for good response is 200rwkw @ 4000rpm. It is a slightly tall order from a 3076r in a reasonable cost effective setup, you will see most making the 140-180 mark. That sort of power and response can be experienced through a highflow, yet the torque and overall feel of the turbo will suffer.

I think you will keep being referred back to the highflow option more than anything else, yet make sure you pick a builder who has well documented results.

Edited by Torques

yer but a highflow bolts straight on. off the shelf aftermarket turbos require a fair bit of modifying to fit

I agree its easier being a bolt on, but if you were to get for example, a 3076 with the nissan rear housing, you just need a T3 spacer plate , oil and water lines and some intake pipeing. so there isnt alot in it.

Ive just gone for a highflow because i care more about response, as soon as i get it together and back from the dyno i will put up some charts :thumbsup:

If you get a 3076. Do not get the Nissan 6 bolt housing. It is restrictive and plain garbage. To fit a 3076 with the proper Garrett housing requires:

Spacer plate ( so comp housing doesn't touch manifold)

Extended studs

Lines

Dump pipe

-all this comes with the kit and is not hard to fit up

Only thing you will need to do is get a 4-3 inch reducer and make up a custom intake pipe

It's well worth it

And for response? I'm hitting 18-19psi by 3500 rpm. On the 3076 with .82 rear housing

If you get a 3076. Do not get the Nissan 6 bolt housing. It is restrictive and plain garbage. To fit a 3076 with the proper Garrett housing requires:

Spacer plate ( so comp housing doesn't touch manifold)

Extended studs

Lines

Dump pipe

-all this comes with the kit and is not hard to fit up

Only thing you will need to do is get a 4-3 inch reducer and make up a custom intake pipe

It's well worth it

And for response? I'm hitting 18-19psi by 3500 rpm. On the 3076 with .82 rear housing

Is your bottom end stock rb25? Also how is your intake setup? 3" metal pipe with pod and AFM infront of turbo or do you have the AFM in the cooler piping?

Is your bottom end stock rb25? Also how is your intake setup? 3" metal pipe with pod and AFM infront of turbo or do you have the AFM in the cooler piping?

Stock bottom ended rb25 mate.

I got the 3 inch intake pipe going to my z32 afm which is connected to my stock airbox with a blitz panel filter. Then have a custom CAI going from the bottom of my airbox to a pod in my front bar

Stock bottom ended rb25 mate.

I got the 3 inch intake pipe going to my z32 afm which is connected to my stock airbox with a blitz panel filter. Then have a custom CAI going from the bottom of my airbox to a pod in my front bar

Sounds good man. Metal or silicone leading to your box? Can you PM me some pix?

Sound interesting ... :)

So you need a spacer for the T3 connector and modify the turbo elbow to match the 3076 exhaust side ...

Is the 3076 much wider compared to the standard turbo?

Who is selling this kit?

Some pictures/dyno would be nice.

Cheers ..

If you get a 3076. Do not get the Nissan 6 bolt housing. It is restrictive and plain garbage. To fit a 3076 with the proper Garrett housing requires:

Spacer plate ( so comp housing doesn't touch manifold)

Extended studs

Lines

Dump pipe

-all this comes with the kit and is not hard to fit up

Only thing you will need to do is get a 4-3 inch reducer and make up a custom intake pipe

It's well worth it

And for response? I'm hitting 18-19psi by 3500 rpm. On the 3076 with .82 rear housing

Sound interesting ... :)

So you need a spacer for the T3 connector and modify the turbo elbow to match the 3076 exhaust side ...

Is the 3076 much wider compared to the standard turbo?

Who is selling this kit?

Some pictures/dyno would be nice.

Cheers ..

Hey mate. Yea you need a t3 10mm spacer to make it fit. The turbo when next to a stock turbo looms huge.

Sorry don't know what you mean about the elbow? You talking about the bend after the compressor outlet or?

I'll get pics tomorrow but it looks VERY stock under y bonnet

Hey mate. Yea you need a t3 10mm spacer to make it fit. The turbo when next to a stock turbo looms huge.

Sorry don't know what you mean about the elbow? You talking about the bend after the compressor outlet or?

I'll get pics tomorrow but it looks VERY stock under y bonnet

This. :)

I dont know why people say 3076 is laggy. But then, comparing any turbo to a stock RB25 turbo its laggy.

I thoroughly enjoy driving Lithiums 300kw 3076 .82 R33. The extra "lag" actually makes the car quite nice to drive. Your not constantly making boost without trying haha. But if you want it, its not far away!

Plus.. the turbo spool noise is orgasmic. :blush:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...