Jump to content
SAU Community

Recommended Posts

AFAIK white smoke = burnt oil. Maybe rings worn a little? If it's happening every time you start the car when cold, it might be worth getting an opinion from a mechanic. There could even be some products you could add to the oil to reduce wear & perhaps stop the smoke. There a Nulon one that I swear by; an 80,000km treatment which I use on all my cars,

Are you running really thin oil Josh? If so, you could experiment next oil change by using the next one up.

Just ask them what it is. A lot of guys are running 0W-30 (or something similar) which is pretty thin. Just changing to a 5W or 10W could make a lot of difference & it's still what I'd consider thin.

I had a crap V8 clunker as a teenager which I ran straight 50 in to stop it smoking pinch.gif .

10w40 feels the best in my engine and offers much more bearing protection.

My car used to smoke a little at startup, then I realised it was the pcv valve sucking all the oil mist up and dumping it into the middle plenum runners. Once I fitted a catch can in line it all stopped.

No water from what I can see. Hmm I know with my aristo I replaced my stem seals and that fixed the issue

I'd be leaning towards stem seals for this, stems seals will also do this after an extended period of idling, then put under load.

Or as Scotty said, PCV issues.:thumbsup:

oil smoke is blue

Not if you have enough of it. A fine mist; yes. Large amounts; no. Turbo shaft seal failure dropping oil into a 600-800deg exhaust billows massive clouds of white smoke.

Hell; a big capacity turbo diesel, running very lean blows white smoke!

I know exactly what you mean; not trying to split hairs, but anyway.

Edited by Daleo

AFAIK white smoke = burnt oil. Maybe rings worn a little? If it's happening every time you start the car when cold, it might be worth getting an opinion from a mechanic. There could even be some products you could add to the oil to reduce wear & perhaps stop the smoke. There a Nulon one that I swear by; an 80,000km treatment which I use on all my cars,

Are you running really thin oil Josh? If so, you could experiment next oil change by using the next one up.

Have been told that the 80K nulon treatment results in hot spots as it builds up in low spots?

Just ask them what it is. A lot of guys are running 0W-30 (or something similar) which is pretty thin. Just changing to a 5W or 10W could make a lot of difference & it's still what I'd consider thin.

I had a crap V8 clunker as a teenager which I ran straight 50 in to stop it smoking pinch.gif .

That V8 clunker would have worn out even quicker as it had less protection at start up and until fully warmed up.

IMO "stop smoke" type additives and thicker oil are a bad idea. They might mask the symptoms but will also accelerate the wear that is causing the smoking. Keep topping up until sorted.

Is it using oil?

Edited by Old Gregg

Have been told that the 80K nulon treatment results in hot spots as it builds up in low spots?

That V8 clunker would have worn out even quicker as it had less protection at start up and until fully warmed up.

No, haven't heard of that. Will ask around..

No protection at startup? Not if it had an 80K treatment in it :rolleyes:

Actually, I ran Slick 50 in those days. I could run the engine without oil if I wanted. Then it wouldn't blow smoke, but was too noisy pinch.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...