Jump to content
SAU Community

Recommended Posts

Hi Im interested in your front diffuser if you have? Please let me know. Thanks!

What do you mean by front diffuser?? The lining under the front? If that what you mean I don't have it

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Not parting the engine just yet. I don't have the time for it.

Hicas bar I'll try to get off in the next few days, I'll send you SMS.

just PM me if your parting the engine cheers mate

R34 guard lining -- $40

post-39016-0-00987800-1302953335_thumb.jpg

STENVE ! (or someone else) do you know if they are compatible with R34 GTR front bumper ?!?

GTR's are not a bit wider ?!?

....if they are the same, YES i take them both !

Edited by BLITZENN

R34 guard lining -- $40

post-39016-0-00987800-1302953335_thumb.jpg

STENVE ! (or someone else) do you know if they are compatible with R34 GTR front bumper ?!?

GTR's are not a bit wider ?!?

....if they are the same, YES i take them both !

R34 guard lining -- $40

post-39016-0-00987800-1302953335_thumb.jpg

STENVE ! (or someone else) do you know if they are compatible with R34 GTR front bumper ?!?

GTR's are not a bit wider ?!?

....if they are the same, YES i take them both !

they are different. GTR is wider.

  • 2 weeks later...

decided against trying to fix the car. too much effort and i just dont have the time.

all parts are go!

I will courier greddy coilovers, they are not camber tops (no skyline coilovers are?) PM me an offer and i'll either say yay or nay.

Was the car crashed when stolen and also how far away from where it was taken did it end up. I'm down on the mid north coast of nsw, how old are they aswell, can you get photos of them?

Nope no crash/accident damage.

Wasnt taken too far 30min drive from where it was taken

greddys are at most 20,000kms old - they are still on the car. so can take photos but you wont be able to see much.

If there is genuine interest i will swap them out with the JIC's to get proper photos etc.

Cheers

update:

black trans cooler - sold

catch can - sold

pending/hold:

exhaust/nistune - pending payment/on hold etc

Edited by stenve

I need help on how to take off the ECU panel located on the left hand side of the passenger side.

Seems like I can't take off that one little clip that's holding the panel together worship.gif

Please help !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...