Jump to content
SAU Community

Recommended Posts

i would think of running both, i wouldn't like to rely on just one - especially widebands

wonder what the GM (saab etc) cars do in the event of the content sensor failing... maybe just really detuned, it wouldn't actually matter

  • Replies 139
  • Created
  • Last Reply

Top Posters In This Topic

What if the E85 sensor packs it in?

What if a massive comet comes from outer space and crashes into earth?

As long as you change the sensor out every 100,000k or 50k if you are paranoid, then you will be fine. You could also argue about the e85 sensor and changing it out, but at $500 a pop?, hmm.

What if the fuel pump FAILS!

DANGER TO MANIFOLD

Or you could save yourself the hassle and buy the V500 Ecu instead. It's pretty much the same price as the vipec/haltech/Autronic etc but does so much more. That's the beauty of running multi-controllers.

Then you don't need the E85 sensor, you just need a wideband o2 which are approx $125-$150

That might work with an RB but VQ25det is a different kettle.

I havent needed to adjust my map as the Caltex eflex has been nothing but consistent so far, no matter what servo I fill at. I just run a simple wideband and will trim the tune if needed using the injector size adjustment on my Emanage Ultimate.

That might work with an RB but VQ25det is a different kettle.

I havent needed to adjust my map as the Caltex eflex has been nothing but consistent so far, no matter what servo I fill at. I just run a simple wideband and will trim the tune if needed using the injector size adjustment on my Emanage Ultimate.

Why is the VQ25DET a different kettle? It's an engine.

It's good to be able to make those adjustments yourself but what about the people who don't know what they are doing? With the appropriate ECU, it does it for you

i would think of running both, i wouldn't like to rely on just one - especially widebands

wonder what the GM (saab etc) cars do in the event of the content sensor failing... maybe just really detuned, it wouldn't actually matter

Probably no worse to an oxygen sensor or air flow meter detoriating - car simply won't run at optimum performance. I don't think it's much of a safety issue. As we've discussed earlier in the thread, the varying contents of ethanol won't put the car into danger territory unless you're tuned on a knife edge...and factory cars certainly aren't. The factory fitted E85 ECUs probably monitor both AFR and E content to make sure the mix is spot on...AFR might be a backup in case of E sensor failing, or who knows, car may go into limp mode.

Ethanol sensor might be expensive, well, $500 every 50,000km (conservative estimate here) I can easily live with...and changing it over for another one would be no harder than doing your fuel filter.

wideband is more useful than ethanol sensor imo, because with wideband you can adjust the tune perfectly to suit, where as with ethanol sensor you are only guessing how much to adjust it by.

stoich for ethanol is 9:1, and gasoline is 14.7:1. Say if your using a gasoline wideband, and running ethanol, then you're going to still read 14.7

So I'm quite confused, unless I'm missing something here?

If not another solution is to run 2x types of wideband sensors, 1x ethanol, 1x gasoline.

if you have it tuned for 14.7 on petrol and throw in e85 its not gonna stay at 14.7, it'll be down to around 11:1. easiest way is to always leave the wideband set to petrol and tune to the same afr's as you would for petrol.

stoich for ethanol is 9:1, and gasoline is 14.7:1. Say if your using a gasoline wideband, and running ethanol, then you're going to still read 14.7

So I'm quite confused, unless I'm missing something here?

If not another solution is to run 2x types of wideband sensors, 1x ethanol, 1x gasoline.

I spoke to the guy at techedge about this. The sensor reads a lambda and the converts it back. On my wideband if you want to run a E85 corrected AFR then you just have to change a few settings.. Easy as... OR look at the lambda reading.

I spoke to the guy at techedge about this. The sensor reads a lambda and the converts it back. On my wideband if you want to run a E85 corrected AFR then you just have to change a few settings.. Easy as... OR look at the lambda reading.

Which TechEdge unit do you have?

I have the 2J1...

if you have it tuned for 14.7 on petrol and throw in e85 its not gonna stay at 14.7, it'll be down to around 11:1. easiest way is to always leave the wideband set to petrol and tune to the same afr's as you would for petrol.

Wouldnt it go the otherway? being that there is only 15% Gasoline so would show something like 18:1? or am i thinking about it wrong

stoich for ethanol is 9:1, and gasoline is 14.7:1. Say if your using a gasoline wideband, and running ethanol, then you're going to still read 14.7

So I'm quite confused, unless I'm missing something here?

If not another solution is to run 2x types of wideband sensors, 1x ethanol, 1x gasoline.

You are forgetting its not straight ethanol.

I leave mine on petrol afr's and get it tuned for around 12:1 at WOT that gives me a little play room still incase Caltex change their brew. (and that way I never get confused converting from lambda.)

stoich for ethanol is 9:1, and gasoline is 14.7:1. Say if your using a gasoline wideband, and running ethanol, then you're going to still read 14.7

So I'm quite confused, unless I'm missing something here?

If not another solution is to run 2x types of wideband sensors, 1x ethanol, 1x gasoline.

yeah but if you change the fuel the relative afr is going to be out, it doesn't matter what the number is, it just matters that you realise it has changed and can tune it to suit.

most sensors read lambda anyway and convert it

Exactly, there should be a Lambda table and it will trim/add fuel as required to reach the target lambda.

A failsafe solution is to use a GM flex fuel sensor 0-5v analogue input to detect the amount of Ethanol in the brew and trim/adjust the E85 map to suit and then look into having a switchable map based on less than x% ethanol for a hybrid map/petrol map.

E85 is too inconstant for my liking to be used everyday unless the servo is consistent with their brew.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...