Jump to content
SAU Community

Recommended Posts

So you have seen the light and joining the "forklift" club :thumbsup:

It's not for the GTR... just the POS gts-t- It's got a Trust T67-25g now. The power delivery isn't nearly as savage as I remember your 33... memories lie! It has 40 odd more rwkw and several hundred kg lighter than when I was in the 33 all those years ago- but it just dosn't feel as fast???

I have many mate, located in launceston.

Daniel.

Any ideas on what it might cost to get a couple down south?

I have a couple or 3 in varies stages of pieces all good blocks and cranks ph 63834643

Are you north or south?

Cheers

Justin

It's not for the GTR... just the POS gts-t- It's got a Trust T67-25g now. The power delivery isn't nearly as savage as I remember your 33... memories lie! It has 40 odd more rwkw and several hundred kg lighter than when I was in the 33 all those years ago- but it just dosn't feel as fast???

Any ideas on what it might cost to get a couple down south?

Are you north or south?

Cheers

Justin

Dale (dbgtst) is up north.

Ahhh the old days when 245rwkw was fast. lol

I look back thinking I should have just been happy with how it was instead of wanting more power.

But the new setup should be interesting....

Sorry didn't get a chance to go for a drive out to the shed on the weekend. But I definitely have a complete set of stock S13 suspension :thumbsup:

Engine mounts are SR your after I'm taking it?

All good cobber Im not in a huge rush so when ever you get a chance.

Im just chasing up everything I need so when I start working on it again I can continue on with no/little interruptions thumbsup.gif

Cheers, I did spot that and sent him a PM but didn't hear back.

RB26 Custom Made JE pistons, 86mm bore, made specifically to use factory rings, world reknowned for being the best rings available. Brand new in packaging, comes with pins and spiral locks and a full set of new factory rings.... $1100

R34 GTR Tomei Type A Poncams, 260in 252ex 9.15mm lift, brand new in box, justjap want 1400, works in any rb just need to use R34 crank angle sensor. sell for $800

R34 GTR N1 block, split bore, needs one sleeve then better than new! $1000

R34 GTR 18" Wheel center caps, immaculate condition, set of 4 $120

SR20DET .2mm oversize factory pistons, brand new in boxes, retail over 300 each, with rings, sell the set cheap $500

SR20DET cast iron factory turbo manifold, as new low km hardly even been hot $120

1972 Triumph 2.5L PI (injected) complete car suit restoration, has engine and all running gear, two spare heads, two manual gearboxes, with one overdrive, all chrome trims immaculate, brand new door and Windscreen rubbers, shell is as it good as it gets, next to no rust, no damage. $1500 or offers, keen to move, need shed space.

Let me know!

Ok so I'm all sorted out for dirty 30 gear...

I did broked my clutch m/c though...

Anyone have a r33 gts-t clutch master cylinder???

i do , can't get to it until friday though, speaking of , has prizo given you those wheels yet??

WTB: std heat shields for rb20/25 turbo

and eoi my hks gt2530 , comes complete ready to bolt on (water/oil lines and hks dump) pm me

i do , can't get to it until friday though, speaking of , has prizo given you those wheels yet??

WTB: std heat shields for rb20/25 turbo

and eoi my hks gt2530 , comes complete ready to bolt on (water/oil lines and hks dump) pm me

hey Toff... I'll call you next week about the m/c. Na havn't got the wheels yet- are they off the laurel?

Cheers

Justin

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...