Jump to content
SAU Community

Recommended Posts

I much prefer the D-jetro option, speak to your tuner though they should have a preference...

Cheers matey im seriously considering going this route and being done with it but my tuner has said that the car will be alot smoother and nicer to drive with normal power fc and afm's as opposed to d-jetro and a map sensor.. How do you find the d-jetro when your holding a certain speed on freeway and when your on off the throttle in traffic etc?

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804279
Share on other sites

Cheers matey im seriously considering going this route and being done with it but my tuner has said that the car will be alot smoother and nicer to drive with normal power fc and afm's as opposed to d-jetro and a map sensor.. How do you find the d-jetro when your holding a certain speed on freeway and when your on off the throttle in traffic etc?

That sounds like your tuner doesnt know how to tune d-jetro properly, so if you stay with that tuner, use afms.

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804324
Share on other sites

Did you get any problems with the Afm's voltage spiking to much under light on/off throttle causing the car to stutter or hesitate and sometimes cause it to stall?

this only occurs if the AFM are too close to the inlet, and reverberation etc.

if its spaced as far as possible, these issues seem not to occur

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804406
Share on other sites

agree, djetro and ljetro (ref DVS32R)

both are the same to tune and setup, and i think from memory the djetro takes longer as you have to work so much harder at the transient throttle process more to get it nice, vs AFM that is bulletproof on the factory maps on the powerfc, ie you dont have to focus so much on that area (from no throttle, to light throttle)

both will make same power and response

but will perform differently as far as mapping and scaling are concerned

but back on topic,

you should not max twin Z32s with T04Z

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804875
Share on other sites

This is the log from my 460awkw dyno run. 26psi 2530's

The Z32's have some voltage left but the 800cc injectors are out...

Jebuz! Is that on 98? Do the HKS turbos make more power than the -5s? I thought 400awkw was the limit of 2530/-5s on pump.

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5805708
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...