Jump to content
SAU Community

Recommended Posts

Much cheaper than the kit they copied though. Much like their Geomaster knuckles... Speaking of which, if they retained standard ackerman angle, I'd be all over that shit. 50mm drop spindles FTMFW.

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I've just got rid of HICAS because the rear was out of control.... Was just doing whatever it felt like

Yea thats what i was going to suggest, bout to do the same on mine actually, rear is a little unpredictable at times.

just jap have a lock bar for i think $100, and looking at the DIY it doesnt look extremely hard to do.

Did you just chuck on a lock bar?

Driftworks have a nice kit that replaces the ball joints etc and all, bit costy though :/

yeah just a lock bar, it wasnt that hard to do, but you need a wheel alignment after, had some pretty epic toe in lol. I just adjusted it visually for the drive to the alignment place.

those that may not have Nene in their facebook here is one of her status updates a very grim warning

Janene Fulcher

At Elizabeth Centre when putting your children on the little rides. If an Old Lady comes up 2 u & starts poking her tongue out Sexually at your children Report her straight away. When my mum & I said we dont do that she kept going & i mean sexually poking her tongue out she then tried to get closer and closer to sienna & we are not exactly sure but it looked like she was going to pick her up.This happened to a friend of mine today! it is being treated as an attempted abduction by police. Janene

stage 2....pfffftttt

more car less camera Dave

Should be sufficient for the power I'm chasing. Don't need new springs and such with these either.

Hahahah, yeah... Now that I realise that money could've covered new wheel bearings, I do slightly regret it.

Slightly.

lol,

fitting up mine in a fortnight and cant decide to tune on flex or not. pros: it would be awesome and most likely make 310-320 ish. cons: that power would be useless, and if towing plans fall through for winton id have to take 400L with me. lol

those that may not have Nene in their facebook here is one of her status updates a very grim warning

yerp that my was daughter that Nene's talking about...Luckily the wife and mother in law were onto it!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...