Jump to content
SAU Community

Recommended Posts

  • Replies 163
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Wheels...what wheels.

Both the LHS have bits missing off them pinch.gif

All the arms are back on the car and it drove ok. Just needs a wheel alignment now. I'm guessing the front LHS hub and mounting points for the tie rod and the lower arm may have moved a little.

But time will tell.

Lol did anyone actually read the new supp regs in regard to the fire ext. mounting? Not sure if this has come directly from CAMS (wouldn't surprise me!) but the supp regs read:

b) Must be fitted with a fire extinguisher securely mounted on a metal bracket with metal straps within the cabin and readily accessible to the driver whilst still in the seat belt or harness and which complies with AS 1841 (save that extinguishers which meet AS 1841.2 are not permitted), and be of at least 900gms capacity. Halon/BCF extinguishers are not permitted. The extinguisher and the bracket must be a compatible set, (i.e. as supplied by the manufacture of the extinguisher.) The extinguisher should be retained within the bracket by at least one (1) metal strap. The bracket should be secured using a minimum of 2, Grade 6 or greater bolts, of a minimum 6mm diameter, and self - locking nuts. A suitably sized body washer may be required to provide extra support for the bracket. The securing system must be able to withstand a 25g deceleration.

The part in question is the bit in bold regarding Grade 6 bolts. There is probably no way that the scrutineers on the day are going to check the markings on the heads of the bolts 8), but the problem is that grade 6 bolts are no longer made and herein lies the problem....The supp regs say grade 6 or greater, but the next grade of bolt is the grade 8. Sure this is a 'harder' bolt but is prone to breaking due to the brittle-ness from the treatment ie under load it is more likely to shear the head off. The lower grade 5 is the bolt used in automotive apps as it is still 'hard' but due to the lower level of heat treatment is more likely to stretch under load rather than shear.

So bottom line, I'm going to use grade 5 or 8.8 bolts....

lol @ self tapper.

Have a read of the entire reg though Ant, its all pointless anyway/not ever followed.

There is no chance in the world, strapped into a harness, that you'll be able to reach the extinguisher unless its bolted to the roof above your head!

Given the purpose of a harness is to stop one from moving!

Have a read of the entire reg though Ant, its all pointless anyway/not ever followed.

There is no chance in the world, strapped into a harness, that you'll be able to reach the extinguisher unless its bolted to the roof above your head!

Yeah I know....but I'd be kicking myself if I turned up, paid the money and they knocked me back because of something so small :(

Hy Ant, what's your previous best at Sandown?

Sandown makes me scared so prev setup only yielded a flat 1:23. While I will be aiming for teens, I will be held back by the fact my balls are smaller than usual at Sandown :yes:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...