Jump to content
SAU Community

Recommended Posts

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

I hear they are almost 2000rpm laggier than -5s?

Dyno sheet?

http://s1206.photobucket.com/albums/bb446/nismoboy_r34/?action=view&current=IMG_0835-1.jpg&t=1315813508740

it doesnt drop off boost at the end, the cooler piping pops off.. not sure what the -5s do but im sure its not 2000 rpm slower there pretty much on full boost at 5600

http://s1206.photobucket.com/albums/bb446/nismoboy_r34/?action=view&current=IMG_0835-1.jpg&t=1315813508740

it doesnt drop off boost at the end, the cooler piping pops off.. not sure what the -5s do but im sure its not 2000 rpm slower there pretty much on full boost at 5600

full boost around 5900, with cam gears, was the poncams dialled in as well, still laggy for the street imho

http://s1206.photobucket.com/albums/bb446/nismoboy_r34/?action=view&current=IMG_0835-1.jpg&t=1315813508740

it doesnt drop off boost at the end, the cooler piping pops off.. not sure what the -5s do but im sure its not 2000 rpm slower there pretty much on full boost at 5600

Going off the graph its 6000rpm.

That's worse than GTRS which are what, 150-200 more?

Can tell you now if its not 2000rpm, its not much less for -5s

  • 2 months later...

Hi , Signed up an account to replay to this thread :D

I have an R33 GTR with these turbos and have had them running for aorund 8000klm now .

a couple of things to know :-

mine had to be run in for about 1-1500klm because of the bearing type

Use a thinner oil for the engine , i use 10w30 redline - many use alot thicker oil and this will make a big difference to turbo lag with drag on the bearings.

Use the factory manifolds unless you have other mods which need otherwise. The manifold to turbo flange is smaller on the factory units increasing gas veocity into the exhaust side of the turbos making them spool at lower rpm . The expreme setup has a larger opening which breaths better at higher rpm but reduces exhaust gas velocity at lower rpm- this makes a big difference with spool up at low rpm.

Use poncam b's , they increase duration of the opening of the exhaust valve by 5 degrees NOT lift - they are easy to install and increase exhaust gas pressure making a noticable difference. you dont need adjustable gears for this - they are pegged for stock cam gears . Adjustable gears are not really required for mild tuning like this.

Mine start to spool at 3200 rpm , have fully spooled up to 1bar at 4000 rpm and keep this steady until redline.

Im upgrading my fuel system and plenum this winter along with arp head studs and a cosworth head gasket so hoping for 1.2 bar next year reliably :)

Once everything is finished ill get a dyno sheet and post it up !

7655 sounds a lot like garret gt2876

Going to jump on the computer in a min. Will confirm wheel sizes then

edit - 68mm comp exducer 6/6 blade wheel and 56mm turbine wheel with 12 blades

and according to tomei still journal bearing

So to me and my quick look around, they are a TD05-20G in custom housings

I've decided to pull mine off and change to a single turbo set up! They are advertised in the for sale section if anyone is interested,

I never turned them up, on 12psi they started making boost at 3200rpm & were agressive once on 12psi at 4000rpm.

and surprise surprise, the ARMS8260's look to be a TD06H turbine wheel with possibly a Garrett GT 76.2mm comp wheel (its isnt a 25G wheel as they are 78mm)

You clever bugger, you seem to be right about them using MHI parts. So all they have done for these turbos is add custom housings and mix/match MHI/Garrett parts.

and surprise surprise, the ARMS8260's look to be a TD06H turbine wheel with possibly a Garrett GT 76.2mm comp wheel (its isnt a 25G wheel as they are 78mm)

A forum member on Club high rollers EZYWIN has the above turbo's his doing back to back testing from -5 this week according to his forum update. Pretty sure it made 530awhp on E85 -5 tuned by godzilla motorsports.. Lets hope for something a little more impressive than the smaller tomei turbo's. :domokun:

Use a thinner oil for the engine , i use 10w30 redline - many use alot thicker oil and this will make a big difference to turbo lag with drag on the bearings.

Have you had 50 or 60 in it? How much effect was it having?

I certainly wouldn't be going that thin (on hot) with a RB26. Least of all just to help crud turbo's spool.

Update from CHR:

First things first. Thankyou to GODZILLA MOTORSPORT, Mark and Darren for there on going passion to my car and the overtime they have spent on EZYWIN. Well those Tomie turbo's Kick Arse and make power. First Dyno Run 530hp @ 17psi at all 4's, that power equals the power i had with the garrett -5's set up with 24 psi. So we made just over 600 at 25 psi. Happy figure at 595 @ 24 psi. So there is a little down side LAG 5000 rpm then Hello. Went for my first drive today and oooo mummaaa powerplay and willowbank here i come. Tomie quality a big yes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Kinda glad I never got to this ..    https://www.facebook.com/groups/1483859159195077
    • @GTSBoy This method was able to get readings of -10 to -2, so it looks like its monitoring.  Now I need to figure out why the vacuum on the line provided isn't alternating with manifold pressure.  I went with 2 lines that an RB25 tuner recommended but I'll get a longer hose and try directly off the back of the manifold.  He may have been used to OEM intake setups while I have a DBW setup that removed the MAF and IACV.  
    • I work at a car detailing and tinting shop called Quark which gets all manner of German cars in usually (mainly due to a contract with Mercedes Benz Kita Osaka, BMW Nishinomiya and others) but every once in a while something special comes in, like a fully restored 1972 HS30 Nissan Fairlady 240ZG... The shop owner had immediately started applying film to the windows as soon as it was in the shop so the interior was completely covered in towels and plastic sheets. But I could get a few photos of the engine bay which was restored like new. Such an amazing car to see in pristine condition in Japan these days.  
    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
×
×
  • Create New...