Jump to content
SAU Community

Recommended Posts

1. ARX rims are 18 x 7.5 JJ, +40 offset.

2. I don't have any recommendations for tyres yet but the tyre placard says 225/55 R18 97H, although my ARX has 235/50 R18 101V (these came with it when I bought it). Having said this, when I upgrade my wheels I'll be looking at a larger rolling diameter to hopefully correct the speedo and maybe even improve the fuel economy.

3. In the "M35 - Light Changes" thread M35 - Light Changes recently Duncan (Dunc) posted a photo of the indicator bulb. Basically it is a larger version of the parker (T10). I think they are known as T20 and it should be 21 watts as specified in the handbook. I'm fairly certain the rear bulbs are the same as the front.

Cheers

  • Replies 193
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hi chaps..

Question - Does anyone know if the VQ25DET turbo to dump gasket is the same as the RB26s? Will install a new system soon and need to know.

Cheers all..

Generally the stock one will go the distance. It is good quality and still using the stock one after turbo change 4.5 years of driving.

Generally the stock one will go the distance. It is good quality and still using the stock one after turbo change 4.5 years of driving.

+1. I think mine looked perfect when it came out but put it back with a smear or hi temp silicon on both sides just to be sure.

High temp silicone will go hard and brittle on the turbo housing Leon, I only use it if the flange wont seal now.

As there is no real pressure after the turbo the gasket isnt critical, it should be fine even if its cracked. Our turbo outlet gasket is VQ specific and was only on the VQ25det's and VQ30det's, you will need to go through Nissan for that one.

The pre turbo gasket where it bolts to the manifold is a standard T3 gasket and should be replaced whenever the turbo is removed with a good multi layered stainless gasket. Pressures in the manifold can be quite high.

Part number for the turbo gasket is 14445-4P200 in case you need it. For reference it was only used on Stagea (VQ25det) and F50 Cima (VQ30det)

This may help.

http://justjap.com/store/product.php?productid=20105&cat=&page=1

High temp silicone will go hard and brittle on the turbo housing Leon, I only use it if the flange wont seal now.

I hope not! I'd be royally peed if I have to remove the dump again. But I had a look at the packet & it's temp rated for turbos.

In any case, it was only a smear, more to hold it in place than anything else. It all seems OK till now & been on for a while too - see what happens in the next few years.

i have a spare for each end, but im pretty sure you can buy new ones. if you get stuck let me know, id really rather sell both as a pair or with the spare rack i have

how much u sell the pair for?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You know how your car rolled through a fence in your last jacking escapade? Scissor jacks increase the likely hood of that sort of thing happening immensely!
    • http://calfinn.com.au/product/1500kg-standard-trolley-jack-cj-2t-c/1500kg-standard-trolley-jack-cj-2t-c   I have this and fits under a S3 33 GTR with no issues. Purchased in 2009 and not one issue. It was $950 back then. Not cheap but something so important isn’t worth cheaping out on.
    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
×
×
  • Create New...