Jump to content
SAU Community

Recommended Posts

Quick question ive got an auto r34 gt-t currently with safc II was looking to upgrade from that to a nistune, would there be any problems since its auto?

NIStune is actually the only real solution for you if you want to remain auto.

The only real difference between PowerFC and Nistune is that with Nistune

you have a full blown PC-Interface and you can log/tune/store your maps on a laptop.

That's why I bought Nistune.

With PowerFC you need an additional add-on called DataLogit to have that kind of connectivity.

PowerFC=Tried, tested and proved; fire and forget solution.

Nistune=Better connectivity, a bit more hassle to install.

Cheers :)

Ok so im not gunna make any substantial power gains with a power fc then?

Best off just keeping the nistune and getting it re-tuned when i get my injector and turbo upgrade then?

Can i get some opinions of good RB25 tuners in sydney who can work wonders with my nistune?:thanks:

Edited by Torques
  • 5 months later...

sorry to drag up an old thread guys, but i was wondering if someone could help me.

I purchased an R33 s1 about 6 months ago and have only just looked at the ecu this weekend. I googled the numbers on the ecu cause it had a sticker on it.

according to other forums, its a 300zx ecu ( I assume this is a Z32 ecu).

what mods can this support? i have 725cc injectors and a super t 70 i wanna put on the car.

Also will i need to get a z32 afm?

thanks guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...