Jump to content
SAU Community

Recommended Posts

  • Replies 259
  • Created
  • Last Reply

Top Posters In This Topic

Because they are better...

Maybe to some people but honestly not for me. I am happy with my RB26 and i would have never considered an LS1 when doing my engine swap.

If they were that good Reece McGregor would have ditched trhe RB26 and put a V8 into his GTR but something tells me the mid 7 he runs with his RB is more than adequate :D

I wonder how many seconds you'd get with infinite boost before you did the headgasket or put a hole in a piston.

Any one keen to try it out? : D

With a good tune i think you may be surprised. The exhaust wheel would probably give up before the engine i reckon

Edited by ido09s

With a good tune i think you may be surprised. The exhaust wheel would probably give up before the engine i reckon

How do you tune for infinite boost? On a stock turbo maybe. But on a steel wheeled turbo, all overboosting is going to do is super-heat the intake air and cause detonation.

How do you tune for infinite boost? On a stock turbo maybe. But on a steel wheeled turbo, all overboosting is going to do is super-heat the intake air and cause detonation.

How does anyone tune a Pro Turbo car when they run 50psi+. Takes a fair bit of knowledge and some skill to do it right the first time, but its done on a daily basis now so its not impossible

There would obviously be limitations to the stock bolt ons, but lets assume they have been changed to cope i am sure the engine would last longer than most would expect.

Maybe to some people but honestly not for me. I am happy with my RB26 and i would have never considered an LS1 when doing my engine swap.

If they were that good Reece McGregor would have ditched trhe RB26 and put a V8 into his GTR but something tells me the mid 7 he runs with his RB is more than adequate :D

OK, RB26 vs LS1 is a little different as the RB26 is paired with a pretty good 4WD system. If someone were to figure out how to pair ATTESA with an all alloy V8 only purists would stick with the RB26 :)

How do you tune for infinite boost? On a stock turbo maybe. But on a steel wheeled turbo, all overboosting is going to do is super-heat the intake air and cause detonation.

Infinite boost is infinite air, so you would simply need infinite fuel :laugh:

thats why i said get a nistune board and a tune, i'm fairly certain the standard injectors and fuel pump could supply enough fuel for 15psi...

my injectors were nearly at peak duty on 0.98bar so i believe im right about 15 on stock killing the engine. let alone stock turbo.

I say stop being a blouse and pick something faster to aim for. A stock LS1 is just a boat anchor and i dont know why anyone would want a Skyline being compared with one.

Why not choose a Veyron, or a Koenigsegg CCXR. Surely this sort of performance would be a lot more appealing :D

I had to laugh at this though..... clearly our laws arent doing enough and obviously do need some reform.... ie school kids should stick to a PS3 and GT5 and most certainly should not be let loose in even a stock Skyline, let alone a modified one.

"I have been on P plates for 3 years now but in less than a month I will graduate to my full license. I know the majority of people on here agree with keeping P platers out of high powered cars is a good idea and I cant say i disagree. But these laws definitley need an overhaul, it is clear that the people who came up with these laws don't know much about cars and as such, shouldn't have been put in charge."

Oh and this is absolute GOLD!!!!!

"The reality of weather you should be in a high powered vehicle or not comes down to your attitude, not your age."

Not that i would think you could be bothered to read through that garbage but it just got worse and worse lol.

How does anyone tune a Pro Turbo car when they run 50psi+. Takes a fair bit of knowledge and some skill to do it right the first time, but its done on a daily basis now so its not impossible

There would obviously be limitations to the stock bolt ons, but lets assume they have been changed to cope i am sure the engine would last longer than most would expect.

Yeh when you set a boost controller to 50psi, that's different than just letting the wastegate free-boost.

Infinite boost is infinite air, so you would simply need infinite fuel :laugh:

And timing? :P Boost does not = air volume.

I dont think the 6.0L v8 is going to get beaten with only $1000 spent on the rb,

theres too much torque and outright nasty grunt , i really think you'd need a gt30 to hose one off convincingly

even if you have enough power , how good are you at launching the thing?? if you dont get a sweet launch then your toast!!

and if the v8 recieves some cams and extractors and tune, then just give up lol, or spent some big money..:whistling:

remember you'll lose your licence if you do 30k's over speed limit which is too easy ...pinch.gif

Edited by SliverS2

and if the v8 recieves some cams and extractors and tune, then just give up lol, or spent some big money..:whistling:

I was gonna say, what if your competitors' V8 had any amount of money sunk into it? It's a pretty steep uphill battle!

I dont think the 6.0L v8 is going to get beaten with only $1000 spent on the rb,

theres too much torque and outright nasty grunt , i really think you'd need a gt30 to hose one off convincingly

even if you have enough power , how good are you at launching the thing?? if you dont get a sweet launch then your toast!!

and if the v8 recieves some cams and extractors and tune, then just give up lol, or spent some big money..:whistling:

remember you'll lose your licence if you do 30k's over speed limit which is too easy ...pinch.gif

You're just comparing the engines. You forget they happened to put them into an outright oil-tanker of a car.

As previously mentioned, the R8 is not a bad area to set the bar at. The VX runs what, 13-flat? Easily achievable in a mildly modified Skyline.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...