Jump to content
SAU Community

R33 Running Rich As f*k !


G3TINQ
 Share

Recommended Posts

I got my car tuned at saddin yesterday he said my car is running to rich couldn't tune it properly.

Mods I've got

Fmic

2-1/2 inch exhaust

Apexi pod

Walbro fuel pump

Stock turbo

Stock afm

Avc-r

I just put in s15 injectors b4 I got it tuned I think they are 440cc is that the problem or afm need some help ? How would I stop running it so rich?

Link to comment
Share on other sites

I got tuned because of avcr am the injectors I put in nut wasn't able to tune due to running to rich Amy other ideas I'm gonna chafe me afm 2 day n put my stock injectors back in

Link to comment
Share on other sites

no, emts (and others) mean, what ECU are you using to support the different injectors?

you cant just change injectors and expect the ECU to figure it out, you need to tell the ECU what injectors you have, if non-std 370cc

your options are

remap the stock ECU

get a piggyback ECU option

get a stand alone ECU

either will let you run larger injectors. with STD ECU and anything other than 370cc injectors your car will run like ass and it's a timebomb

im surprised the tuner didnt check or ask you or refuse to tune it with std ecu and different injectors

did you tell him it had non-std injectors? did he ask what ECU

or have you just failed to list it here?

Link to comment
Share on other sites

no aftermarket ECU is your prob.

as per Paulr33, the stock ecu cannot handle larger injectors.

so either change back to stock ones or you will need a programmable ecu like a PowerFC as well.

M

Link to comment
Share on other sites

there is nothing to figure out or nothing to do your head in.

it is a simple yes / no question.

if you have a remapped ecu, aftermarket ecu, piggyback

a) get it remapped / tuned again

if you have the standard ECU

a) remap the stock ECU

b) get a piggyback ECU option

c) get a stand alone ECU

or your last option

remove the aftermarket injectors

YOU

CANNOT

RUN

NON

STANDARD

INJECTORS

WITH

A

STANDARD

UN-MODIFIED (not remapped)

ECU

Link to comment
Share on other sites

yeah you dont need 440cc injectors with std turbo

the std turbo will run out of efficiency before the stock injectors do

so sell them and spend the money you get back on a piggy back or ECU remap

the piggyback or ECU remap will add a bucket load more average power everywhere and make the car heaps quicker

you should peak 200rwkw with those mods + ECU remap or piggyback

but the average power will be up heaps more over the std ECU and boost controller

plus youll have to avoid the factory boost R&R around 10psi so its a crap setup even if you just ditch the injectors and tune it

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Transmission synchros feel pretty bad at this point in my car and sometimes the clutch feels like it has an inconsistent engagement point in the pedal travel. I figure if I'm going to swap in a new transmission I may as well also put in a new clutch. Obvious candidates are ATS's pull-type twin plate carbon clutch, Nismo Super Coppermix Twin, or some organic clutch option I haven't figured out yet. I have searched this stuff to death at this point and still don't feel all that confident in making a decision. Target power is not much. ~330 kW at the wheels max. I ballpark the torque spec at 600 N-m. The stock clutch feels a little light so a little heavier is ok but I would say no more than 15-20% additional pedal effort. For some reason most clutch manufacturers want to keep this stuff a secret but the Coppermix Twin is 950 kg clamp load so I figure it can't be too much heavier than stock. The hang-up I have is some people mentioning that the clutch is very grabby which sounds like a pain. The stock clutch is almost too easy to modulate so I don't mind if it requires more precision than that but I don't want to deal with something that feels like I'm getting rear-ended at every traffic light. Also I see some mention of the release bearing carrier sizing requiring some work which sounds like something that might complicate installation? It would be good to know exactly what is needed here for a 1995 R33 GTR. The ATS clutch is supposedly the best but I've seen some complaints that they wear out easily and also slip when cold. I don't know how much of that is true but the cost is also huge compared to even the Nismo Coppermix twin plate. It's also unsprung which normally I would reject immediately but supposedly carbon clutches don't need it. The higher clamp load at 1300 kg is also a little concerning but to me more clamp load seems like it inevitably means more pedal effort and also more strain on the engine crank thrust bearings.  This is a street car and despite being a weekend car I seem to spend a lot of time crawling in severe traffic congestion with it anyways so I will gladly pay to have something that is easy to drive on and will hold the power with no unexpected headaches. I really don't want to do a clutch twice.
    • Grease the poly bushes as your first order of business. Moly grease. Spanner check everything else. Inspect LCA inner bushes.
    • It's usually associated with a muffler. Often in the middle of the muffler, sometimes at an inlet. Not removable by just slipping something out. usually needs butchery (read outright replacement of the muffler). There's absolutely nothing magic about any Jap exhaust brand. Totally generic. Totally replaceable with anything else that will do the job. I've replaced the centre muffler in mine a couple of times.
    • I've had a 9280, 9280's in stock form produce a bit of a whine when coming on unlike the 9180 so you may already like the turbo sound as it is.
    • So everytime the car is changing momentum, say you were going forward, and then you brake, itll do the creaking  and then wont happen when you brake again while still going forward. but once you put it into reverse and then you brake itll creak, but wont creak any more after while still reversing. And then again, when you go back to forward and the first time you brake, itll creak.  ( note will only happen the first time you brake when traveling a direction ). Wont happen, when youre going up speed bumps or hitting a pothole etc. Sound comes from Front left area.    I'm unsure as to what might be causing this sound so if anyone has any suggestions please. Ive got a set of R34 GTT brakes that I will be installing soon too. (and disregard the gutter rashes, from previous owner(s)... ) Otherwise, it has a shot set of Tein Coilovers, original bushings except poly on tension rods. Car has 138k kms. Video reference :   
×
×
  • Create New...