Jump to content
SAU Community

Recommended Posts

I'm happy to pay the same, I would rather pay more and not have to many people there, I think I did 30 runs on the day, for a full day of runs I cannot see the problem.

I'm in for sure next year, going for at least a 11.999.

My best day at the drags ever.

  • Replies 114
  • Created
  • Last Reply

Top Posters In This Topic

Thanks Chuck :thumbsup:

Fair nuff.. Dudes at WSID suck i guess..

5 runs on a Wednesday night is a maybe if you get there super early, and no VL smashes a diff off the line and they take an hour to clean up the oil. Apparently there are Sunday off street meets starting up at the end of the month, will run like 6hrs!!

Yes, the first Sunday Street Meet is on the 23rd October:

http://wsid.com.au/?m=events&a=event_page&id=103

With Full Throttle Friday on the 21st.

:cheers:

Matt, plenty of quality shots on the CD - Thanks! :thumbsup:

My fave is attached:

post-4183-0-02275200-1318425822_thumb.jpg

  • 2 weeks later...

Unfortunately that time of year is gone already...

We've locked in the 2nd of June with Sydney Dragway.

Details will be up in a couple of months so people can start paying, but so far, keep that date free... ;)

hmmm better make sure I have 1000cc injectors and a bucket load of E85 before June!!@!

hmmm better make sure I have 1000cc injectors and a bucket load of E85 before June!!@!

You have a target date... Get on it!

PS: Depending on power you're going for, 1000CC injectors may not be enough... ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...