Jump to content
SAU Community

Recommended Posts

Well if u can pick up another caliper tonight it would take about half an hour plus a brake fluid bleed!

Problem is, I don't have either and have never done the brakes before.

oh gosh, wish you were my neighbour Aaron!!!

I remember some 25GT taking like 1 minute in the opposite lane trying to over take someone, that was funny.

There wasn't anything really bad that happened.

Just a lot of overtaking. Dont remember any burnouts or anything.

Edit, I remember justin being fed up with someone going slow in front of him, so he went into another lane and boosted off, only to see a speed camera right in front of him, *slams on brakes*

Srs, that looks like some normal orange, yours is some metalic with some yellowish pearl in it. Looks way better. Your wheels too :P

agree but I would love some of those rear fenders so I can straight my rear wheels

Problem is, I don't have either and have never done the brakes before.

oh gosh, wish you were my neighbour Aaron!!!

Ide help out but I'm in SE subs. Just undo the rear bolts holding on the front face of the caliper and try and in seize it. You should be able to. Then just do em back up. Might get you to where u need to be, and if it does un seize then atleast if it f**ks up on the way u can do a quick temp fix.

But I seriously wouldnt be driving it. If the brake is clamping your going to have some serious heat issues and break something

my 2530 sees the light again! A bit dusty, nothin suss with the actuator. Its stock :ph34r:

Anyone have a foot pump with a pressure dial gauge? Want to check if ive set the actuator correctly... From what I could make from the japanese instruction manual, it says 179mm for 1.0bar. Although heaps of thread still remains. Does that mean I can go for moar? Can someone plz translate the table? Thanks

img0783cd.jpg

img0782uq.jpg

Ide help out but I'm in SE subs. Just undo the rear bolts holding on the front face of the caliper and try and in seize it. You should be able to. Then just do em back up. Might get you to where u need to be, and if it does un seize then atleast if it f**ks up on the way u can do a quick temp fix.

But I seriously wouldnt be driving it. If the brake is clamping your going to have some serious heat issues and break something

Cheers for the advices Aaron! Will give it a shot if not I'll just quickly pop into Brake Plus or something tomorrow and hope they do it fast.

I remember some 25GT taking like 1 minute in the opposite lane trying to over take someone, that was funny.

There wasn't anything really bad that happened.

Just a lot of overtaking. Dont remember any burnouts or anything.

Edit, I remember justin being fed up with someone going slow in front of him, so he went into another lane and boosted off, only to see a speed camera right in front of him, *slams on brakes*

*tsk tsk* Good ol' Justin haha

my 2530 sees the light again! A bit dusty, nothin suss with the actuator. Its stock :ph34r:

Anyone have a foot pump with a pressure dial gauge? Want to check if ive set the actuator correctly... From what I could make from the japanese instruction manual, it says 179mm for 1.0bar. Although heaps of thread still remains. Does that mean I can go for moar? Can someone plz translate the table? Thanks

It says if you run too much boost, there will be danger to the manifold

I'm doing some work with my cousins business to help him out with the social networking side of things / help getting his name out - basically it's a small online JDM car parts store and quickly building in size. Like on facebook if you feel like helping out :)

http://www.facebook.com/jdmracingau

a link to the store is on the facebook page.. check it out

also he's started up a youtube channel for product reviews and events / trackdays etc. and we'll be doing some "driver profile" type videos in the near future - so will need a few different cars / people I'm sure I'll contact some of you about this in the future!

/shameless plug - sleep time now brahz

I remember some 25GT taking like 1 minute in the opposite lane trying to over take someone, that was funny.

There wasn't anything really bad that happened.

Just a lot of overtaking. Dont remember any burnouts or anything.

Edit, I remember justin being fed up with someone going slow in front of him, so he went into another lane and boosted off, only to see a speed camera right in front of him, *slams on brakes*

THAT WAS ME! >.< Bloody bitch next to me was speeding up as I was trying to over take her... Twas rather frustrating... Especially being N/A :-(

As for an incident, there was one overtaking incident on the GOR itself, guy tried to overtake 3 of us at a corner, almost went head first into a semi, would have collected all of us... Twas early in the day, towards the end of the pack (obviously, me being in a N/A)

But f**k, I was driving so f**kin hard to try and keep up on that day!

THAT WAS ME! >.< Bloody bitch next to me was speeding up as I was trying to over take her... Twas rather frustrating... Especially being N/A :-( As for an incident, there was one overtaking incident on the GOR itself, guy tried to overtake 3 of us at a corner, almost went head first into a semi, would have collected all of us... Twas early in the day, towards the end of the pack (obviously, me being in a N/A) But f**k, I was driving so f**kin hard to try and keep up on that day!

lol i dont think i want to partake in the commo charity cruise anymore

I remember some 25GT taking like 1 minute in the opposite lane trying to over take someone, that was funny.

THAT WAS ME! >.< Bloody bitch next to me was speeding up as I was trying to over take her... Twas rather frustrating...

Lol you know you need a faster car when you struggling to overtake a lady :P

I do not condone speeding, stay safe brahs

I remember going up to shepparton, birds saw this.

Alvin was overtaking some bogan in an old xr8, the dude stepped on it and we almost hit an oncoming car (car swerved into emergency lane)

This was in the soarer, and the soarer was missfiring because his pod fell off... LOL

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...