Jump to content
SAU Community

Recommended Posts

Quality cars, my opinion was swayed after driving one!

Swayed in which direction? I drove it straight after driving my Skyline, I couldn't get over how tight and short the gearbox was a how short the clutch throw was. Handled amazingly, unfortunately the paint wasn't as good as I had hoped and the soft top was not so soft... More dry and crumbly

Want me to pick you up on my bike Leigh?

Too soon?

f**ker lol

I was looking at bike rego costs 500cc and over is just over 600 now.. Think I might get a husky 511 (they're actually 480cc) brembos 118kg and 50-60hp $450 rego better

Although do like r6

Swayed in which direction? I drove it straight after driving my Skyline, I couldn't get over how tight and short the gearbox was a how short the clutch throw was. Handled amazingly, unfortunately the paint wasn't as good as I had hoped and the soft top was not so soft... More dry and crumbly

Positively...I never thought they were bad cars, but didn't think anything special until I drove. Basically a big go kart and loads of fun. Gotta give them revs to get them going, but still better in traffic than turbo lag.

I was looking at bike rego costs 500cc and over is just over 600 now.. Think I might get a husky 511 (they're actually 480cc) brembos 118kg and 50-60hp $450 rego better

Although do like r6

Didn't know rego depended on displacement :(

R6 for sure! Though...if you can stomach the looks, the GSX-R600 is the fastest accelerating middleweight...it's marginally slower than an R1 to 100 :O

saw last night an orange gallardo followed by a white modded c63 followed by a white gallardo with green/red stripe driven by a little asian chick on russel st.

asians in all 3....

i died a little inside.

When will it be my turn...?

That's why I got one, can't beat them for the price. Speaking of, that's the best price and mileage I've seen on an 08 since mine...buy it nao.

lol there was an r6 doing "prinny" laps last night with all the bogans

serviced the 2fiddy

sump plug wouldn't tighten properly so i put some sealant on it...

hoping for the best/expecting the worst

When will it be my turn...?

least you'll have a turn :closedeyes:

serviced the 2fiddy

sump plug wouldn't tighten properly so i put some sealant on it...

hoping for the best/expecting the worst

Careful with that one Rimmy, and make sure you check your oil level / for oil leaks before every ride. People have lost their engine oil half way through a ride before, engine seized, come off the bike and died :(

All the little issues with car engines are big issues for bikes :/

Careful with that one Rimmy, and make sure you check your oil level / for oil leaks before every ride. People have lost their engine oil half way through a ride before, engine seized, come off the bike and died :(

All the little issues with car engines are big issues for bikes :/

No idea how to check oil level lol I know it takes 2.6l so I just put it in that much

I started/reved it there are no leaks

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...