Jump to content
SAU Community

Recommended Posts

most important is to have a correct fitting screwdriver, if then doing as Simon has said, and you still cannot get them,

then do the same again except with vice grips around the shaft of the screw driver.

Thanks guys for all the tips, will give it another crack tonight.

Mafia - I did actually try freezing the whole thing, sounds like I got it around the wrong way! Will try the heat option.

:cheers:

need the correct sized screw driver, a way of holding the oil pump so it wont move. pref horizontally, then lean into it with your body weight and try and crack it.

avoid using an impack screw driver thats for sure

Why would you avoid using impact screwdriver I used to be a engine rebuilder and using a impact screwdriver is the only way using heat warps the housing which is a good idea

Had the same problem, use an impact screw driver....

Or what I did was vice the pump, got the correct size driver with a large ring spanner on the handle for leverage,

Then turned it while a mate pushed down and located the screw driver so it doesn't strip out

ive pulled plenty of oil pumps apart none of which have needed heat or an impact screwdriver. i'd say avoid an impact scredriver cause an oil pump is a fairly sensitive thing in a weakish housing.. some people are too heavy handed and too much potential to f**k it up

ive pulled plenty of oil pumps apart none of which have needed heat or an impact screwdriver. i'd say avoid an impact scredriver cause an oil pump is a fairly sensitive thing in a weakish housing.. some people are too heavy handed and too much potential to f**k it up

I pulled apart plent without needing an impact screw driver lol

purchase a screw driver with a hex style shank so that you can fit a spanner on the shaft.

place screwdriver end into screw, give the screw a couple of love taps to shock the thread,

Then use the spanner on your screwdriver to crack that bad boy

I pulled apart plent without needing an impact screw driver lol

purchase a screw driver with a hex style shank so that you can fit a spanner on the shaft.

place screwdriver end into screw, give the screw a couple of love taps to shock the thread,

Then use the spanner on your screwdriver to crack that bad boy

^^ yep, thats what worked for me, once u round off those heads on the screws then its in the bin it goes

You really need a degree in the bachelor of arts thumbsup.gif

If your having so much trouble undoing them with the correct size screw driver, it sounds like its been pulled apart and had the screws loctited previously. They really arn't that hard to remove at all.

As said before though, hex shanked screwdriver.

Sit it outside on a stinking hot day, use gloves to handle it and then do as above^^^^ the extra heat works. If its winter use an oven on low around 50'C and try it.

A bit of low heat will let you undo the impossible.

Well I finally got around to giving it another crack. Used my impact driver and they came out easily haha. Thanks for all the input :)

Also suprised to confirm that Neo's come with an N1 pump as standard.

And at least I know its not one of the Chinese copies!

yeah i mentioned that in another thread as i discovered it not long ago. N1 pumps stronger then people think too...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...