Jump to content
SAU Community

Recommended Posts

Re M35 contact Daniel or one of the boys at Autostrada in Herston Brisbane

Very helpful tell him what motor what transmission etc

Roy

0418276699

Re M35 contact Daniel or one of the boys at Autostrada in Herston Brisbane

Very helpful tell him what motor what transmission etc

Roy

0418276699

Thanx Guys for your help. I saw these. I hope I am allowed to post this.

http://www.ebay.com.au/itm/171747506122?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

http://www.ebay.com.au/itm/361095785439?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Is that your number Serious? or the guy in Brizvegas, I will put the business his way no problem.

Also I bought my M35 about 2 months ago and came on here to find out about it before & after. Had a problem with the Attesa Pump Relay after the 4WD light came on, solved it with help from info I found on here.

  • 7 months later...
  • 6 months later...
On 11/27/2011 at 0:09 PM, Commsman said:

Hi everyone

I have a limited number of cruise control systems for sale. They come with the factory switches for your steering wheel & these have LEDs so you can see what the button function is in the dark.

It will take a couple of hours to install & the details are documented. You only need to connect 4 wires (12V, brake x 2 & speed sensor) to get it working, plus the dash light input (from cig lighter) if you want the switches to light up.

You also get the stalk control which you use to program the unit to work on the factory controls & you can even configure it for various levels of responsiveness (tip - leave in factory settings to start with).

The audio controls come in the same harness so if you have the factory sound system then it will just work.

Cost is $490 delivered for the whole kit - an absolute bargain since these ones are typically $900 installed without the steering wheel switches.

PM me for more details.

Cheers, Leon.

post-76144-0-53643400-1322356065_thumb.jpg

Hi mate! Would like to get one of your cruise controllers on my stagea m35! How to proceed plz? Thanks

chris

Hi sau wagoneers ! Can someone around melbourne or vic be able to help me , i want to buy and install a cruise control on my m35 ! Im new to australia as im an internal student! If someone knows where to go, who to call so i can get it installed properly plz help me ! Thx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
    • Been a busy but productive day. Axle and hubs acquired. All fitted up after a bit of modifying. Need to sort out wider mudguards and running light reflector covers but other than that the trailer is gooood to go !!
×
×
  • Create New...