Jump to content
SAU Community

Recommended Posts

Hey guys ive been searchin the forum for this but with no luck so i will just ask instead (excuse for the noobiness)

I currently have. Volk gtc's Front:235/40/r17 rear:255/40/r17 which are 8's front 9's rear , i have the rear gaurds rolled and i want to know what size tyres do i need (or to get) to have stretched tyres

I also have 25mm neotech spacers that i recently installed into my rear wheels which i found was rubbing, what camber adjustment would i need and ride height to be able to fit it in ( the car is sitting 145mm off the ground from the middle)

Any ideas?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/387308-stretched-tyres-for-an-r33-gtst/
Share on other sites

List the offset so we can tell you?

I run 235's front and 265's rear with only rolled guards. My old 19's were the same and were fine without even touching the guards. You need to list the offset as well as the spacers to work out where the wheels will sit with the tyres. Sounds like you bought GTR offset and are spacing them to a gtst?

List the offset so we can tell you?

I run 235's front and 265's rear with only rolled guards. My old 19's were the same and were fine without even touching the guards. You need to list the offset as well as the spacers to work out where the wheels will sit with the tyres. Sounds like you bought GTR offset and are spacing them to a gtst?

Im not sure about the offset because i bought the car with the wheels on it already so im not quite sure what he was trying to achieve but from the lools of it the fronts are +35 rears +39 but as i said im not quite sure ,

Im not sure about the offset because i bought the car with the wheels on it already so im not quite sure what he was trying to achieve but from the lools of it the fronts are +35 rears +39 but as i said im not quite sure ,

offsets are usually stamped on the wheel somewhere, usually on the inside of the spokes

think my old wheels were 9.5" wide +38 offset with 265's (very small stretch) fronts were 8.5" wide + 35 with 235's (again think they are very slightly stretched.

I have 9" wide + 36 with 265's on the rear now and they scrubbed a fair bit and I had to roll the guards. Just to let you know what my experiences were

Might have to double check the offsets but I think thats about right

You dont need offset to determine 'stretch'

with 8 and 9, it's hard to have any sort of stretch unless you go like 205 for front and 215 for rear which is abit stupid

Sell the rims and get 9 and 10, or 9.5 and 10.5, then get into the stretch game

You dont need offset to determine 'stretch'

with 8 and 9, it's hard to have any sort of stretch unless you go like 205 for front and 215 for rear which is abit stupid

Sell the rims and get 9 and 10, or 9.5 and 10.5, then get into the stretch game

yeah but he wants to know if its going to rub etc. so offsets matter for that. I know offset doesnt effect stretch

offsets are usually stamped on the wheel somewhere, usually on the inside of the spokes

think my old wheels were 9.5" wide +38 offset with 265's (very small stretch) fronts were 8.5" wide + 35 with 235's (again think they are very slightly stretched.

I have 9" wide + 36 with 265's on the rear now and they scrubbed a fair bit and I had to roll the guards. Just to let you know what my experiences were

Might have to double check the offsets but I think thats about right

Thanks mate i will just double check the wheels when i get back home, i might just do that and get 265's when my 255's run out , just got these new neotech spacers which i wanna be able to use in either the fronts or rears, also i dont have any camber on the wheels so their straight as,

Why do you want to stretch the tyre? Fitting a tyre that is narrower than the tyre manufacturer supports would not be legal and will have worse performance than a proper fit?

Or is this just about the ful sik look and handling doesn't matter?

Why do you want to stretch the tyre? Fitting a tyre that is narrower than the tyre manufacturer supports would not be legal and will have worse performance than a proper fit?

Or is this just about the ful sik look and handling doesn't matter?

Hey duncan

Yeh it was just to get a "Sik" look but it sounds like the cons are more than the pros

OK makes sense....just wanted to make sure you were aware it's only a cosmetic choice, not a performance one ;)

Put the best tyres you can afford under it and enjoy, the right tyres really transform a car

OK makes sense....just wanted to make sure you were aware it's only a cosmetic choice, not a performance one ;)

Put the best tyres you can afford under it and enjoy, the right tyres really transform a car

Or in my case its done for maximum clearance so can run more lock lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...