Jump to content
SAU Community

Recommended Posts

In-car video showing the 34 boosting hard on full boost or its not true? Nah man but Im sure we would all love to see

When I get the boost controller sorted and I can

Find an appropriate "private road" or track :yes:

At the moment I haven't kept the throttle down long enough to enjoy, once it starts getting loose in 3rd I back off... Need better rubber for sure

ku36 tyres arent that bad, what width are they on the rear?

265.... Either KU36, RS-Rs or Achillies 123s.... Just cheapies as they won't last long anyway :D

don't waste your $$$ on KU36

they are pretty decent for what they are but kuhmo have increased their price in the last 12 months and you can get Nittio NT05's or Federal RSR for less.

imho for a street car go with the Nitto's or if you can stretch the wallet grab some advan AD08's

I usually run the NT05's all round and with my suspension setup they give me effortless traction in 2nd right up to about 310rwkw (e85 on 16psi) - beyond that i need to think about what i'm doing

don't waste your $$$ on KU36

they are pretty decent for what they are but kuhmo have increased their price in the last 12 months and you can get Nittio NT05's or Federal RSR for less.

imho for a street car go with the Nitto's or if you can stretch the wallet grab some advan AD08's

I usually run the NT05's all round and with my suspension setup they give me effortless traction in 2nd right up to about 310rwkw (e85 on 16psi) - beyond that i need to think about what i'm doing

+1 for AD08's, great tyre. Once they get the heat into them they are awesome

I'm using 265/35R18 RS-R's on the back and they only just manage to grip 2nd with 280rwkw and a toight like a toiga diff (shimmed).

Have you tried them out at Barbs dude? I found my KU36's are ok on the street, but they really come alive when you get some heat into them on the track.

Thanks mate... Will hopefully get it sorted before Texi...

360kw was the highest run... It was run @ 357kw on the final tune for safety... The reason for the different power figures is the 3 boost levels and also the % of ethanol.... My power ranges from 311kw to 357kw depending in boost and E content :)

Hope that makes sense?

Do you have a dyno sheet, or did I miss it ?

don't waste your $$$ on KU36

they are pretty decent for what they are but kuhmo have increased their price in the last 12 months and you can get Nittio NT05's or Federal RSR for less.

imho for a street car go with the Nitto's or if you can stretch the wallet grab some advan AD08's

I usually run the NT05's all round and with my suspension setup they give me effortless traction in 2nd right up to about 310rwkw (e85 on 16psi) - beyond that i need to think about what i'm doing

Don't KU36s last longer than RSR though? I know RSR is a more grippy tyre but they really don't last.

Edited by Rolls

Do you have a dyno sheet, or did I miss it ?

Don't KU36s last longer than RSR though? I know RSR is a more grippy tyre but they really don't last.

The KU36's have a treadwear of 180, the RSR's are 140. So not a huge difference. I know my KU36's lasted about 1 track day and maybe 8000km's, so they don't last either.

The KU36's have a treadwear of 180, the RSR's are 140. So not a huge difference. I know my KU36's lasted about 1 track day and maybe 8000km's, so they don't last either.

What type of driving would that be, around a track ?

would they last longer with normal street driving and occasional short blasts?

What type of driving would that be, around a track ?

would they last longer with normal street driving and occasional short blasts?

I drove it hard at the track and spun out on a couple of occasions, so I have no doubt that took off a fair chunk of life. But I only got in 10, maybe 12 laps. On the street I drive pretty sedately with the odd 1st, 2nd, 3rd bursts. So they don't last very long, but no doubt without the track abuse they would last longer.

I think you'll find that if you don't destroy the compound on the tyres by tracking them hard, doing skids, etc. etc. then they would last a fair bit longer. But I'd be surprised if you got more than 15-20k km's out of them.

I have KU 36 on the front, but they sat for 2 years so maybe hard now? They gripped real well compared to other tyres.... Was happy with them. I have some shit sumitomo or something on the rear hence why I have no grip....

Rolls - sorry mate, I have 4 dyno sheets, just haven't had time to scan them.... I have 98 sheet, gate pressure E85 vs 98, low boost E85 vs 98 and then just high boost on E85.... Will get them

In here and in the RB 25 thread soon.... Sorry over been slack :)

When I get the boost controller sorted and I can

Find an appropriate "private road" or track :yes:

At the moment I haven't kept the throttle down long enough to enjoy, once it starts getting loose in 3rd I back off... Need better rubber for sure

Oh dont be soft mate thats when it just starts getting fun when ya doing 130km/h in 3rd and the rears start breaking loose :nyaanyaa: (even though they are only nankangs) lol Looking forward to checking your setup out at texi next weekend dude sounds like a sweet setup :banana: Hoping my big brakes are gunna be on my car by then too and possibly some semis lol

Haha come say g'day and have a look :) plumb back and low boost will be like light beer through a straw.... But, what can you do :(

For sure dude I might have to wind down the boost too im a track/witches hat amatuer so see how i go lol :whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...