Jump to content
SAU Community

Rb25Det 300Rwkw Where To From Here?

WMDC35

By WMDC35,
in Engines & Forced Induction

 Share

Recommended Posts

WMDC35 Experienced

WMDC35

Posted
Posted

Hey, have an unopened r33 rb25det with 300rwkw, looking for a bit extra, maybe 320-350, debating whether to do rods & pistons or rb30, or just crank boost for 320ish and see how long it lasts :unsure: , it's a road car, whats your thoughts? anyone thats run around 320 on standard motor-how long did it last and what did it get used for? the engine i have is on about 81,000ks and seems mint

how much faster on the road is a 30 than a 25 with the same/similar kw?

cheers!

Link to comment
https://www.sau.com.au/forums/topic/390231-rb25det-300rwkw-where-to-from-here/
Share on other sites
Harey Veteran

Harey

Posted
Posted

Need more details, turbo, fuel, boost level, dyno sheet would also help.

Quick answer is yes an rb30 with the same peak power as an rb25 (both done properly) will be a lot faster on the street as the area under the curve will be a lot more.

SimonR32 Grand Master

SimonR32

Posted
Posted

Crank the boost! You will surprised how long it lasts for with a decent tune, but eventually it will let go :whistling:

In terms of RB30 vs RB25... It really depends on too many factors, some RB25's will be faster, some RB30's will be faster

badhairdave Proficient

badhairdave

Posted
Posted

Add boost until it stops making more power, then a couple more psi so you don't lose power on a hot day, then add some more to account for lower pressure at high altitude in case you drive to the snow next winter.

GTScotT Grand Master

GTScotT

Posted
Posted

someone posted a video of an RB30 with a simple bolt on blowing a CBR600 on the street recently

id say RB30 is awesome on the street...... but yeah,

need more info re the current setup as stated. could chuck a WMI setup in and screw heaps more boost into it

JustinP Mentor

JustinP

Posted
Posted

Yep get a WMI setup, more boost, and retune :P

someone posted a video of an RB30 with a simple bolt on blowing a CBR600 on the street recently

id say RB30 is awesome on the street...... but yeah,

need more info re the current setup as stated. could chuck a WMI setup in and screw heaps more boost into it

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I know this might be a crazy idea but look what I found

http://www.skylinesaustralia.com/forums/topic/389417-300kw-unopened-25-club/

It seems to answer a lot of your questions all in one simple thread.

+1

Please use the search. More than enough info around.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...