Jump to content
SAU Community

Recommended Posts

had to remove my washer bottle filler neck as my battery had to be fully pushed against the chassis.

so gonna have to connect a clear hose and run it from the washer bottle into the engine bay. dodgey but it'll work :miner:

I'll just ditch the stock washer bottle and buy a small universal one. Either relocate it to somewhere else in the engine bay if it fits, otherwise to the boot. Stock one is ugly anyway :P

I'll just ditch the stock washer bottle and buy a small universal one. Either relocate it to somewhere else in the engine bay if it fits, otherwise to the boot. Stock one is ugly anyway :P

washer bottles are overated lol just bin it and dont run one.

A lot of people put the battery in the boot (for cars that don't already have it there) and get a fabricator to make a combined washer bottle/catch can to fit in the available space (some with cut outs for the intercooler piping). I am too cheap for that and I have found that my washer bottle can share the space with the piping by making some new brackets. I may have to go with the flexible filer hose as above^^^ but am not prepared to lose either front or rear washers they are good for an extra 10kw at least!

IAC valves can easily be replaced by a competent tuner. My Plazmaman plenum allowed me to run the stock RB25 IAC (upside down / had to extend two wires) but I ended up pissing it off and replacing it with a piece of flat steel, some silicon and the bolts that normally hold the IAC in place.

Not really, pwr steer idle up, a/c idle up, auto anti stall etc are all required for the niceties of a daily driver.... many afm based ecu's strugle without one. Nistune for one is happy to make upwards of 500rwkw but does not like having the iac removed.

if your ecu allows it and your not fussed about having a higher idle than std etc than yes it can be tuned around (mostly map based ecus).

The only people who seem to get good results with these are guys who need to justify the fact they sold it to the customer.... yes we tuned heaps yes they work (like std) would i put one on my own car ... no.

i wanted to run mine without IAC but my tuner advised against it for the above reasons for a/c, power steering etc as it is recommended to run it.

if i could, i would remove it and tune without it as it makes my engine bay look so messy.

Plenty of space in the boot for a washer bottle! - (no I'm not joking, that's where mine is).

Worth popping your boot to fill it up when you have this happy.gif

plazamann1328659221.jpg

Off topic here but gota say those rims on black look crazzy!

Off topic here but gota say those rims on black look crazzy!

screw that.... that whole car is super sexy.

Thanks! Looks totally different since this pic - alot has changed. Sadly it was the only shot I had that showed my plenum so I had to use it.

The plazmaman makes you actually look forward to changing plugs, instead of putting it off because of the annoying cross pipe set up :D

You mean the loss in torque? That's got nothing to do with the motor, it's the length of the runners on the intake. As a general rule, shorter runners = less mid-range more high end, longer runners = more mid-range less up top.

  • 2 weeks later...

Not really, pwr steer idle up, a/c idle up, auto anti stall etc are all required for the niceties of a daily driver.... many afm based ecu's strugle without one. Nistune for one is happy to make upwards of 500rwkw but does not like having the iac removed.

if your ecu allows it and your not fussed about having a higher idle than std etc than yes it can be tuned around (mostly map based ecus).

The only people who seem to get good results with these are guys who need to justify the fact they sold it to the customer.... yes we tuned heaps yes they work (like std) would i put one on my own car ... no.

Niceties of a daily driver? Lol. Sometimes I forget that my priorities don't extend to giving a shit about those things. Still the car functions perfectly well, doesn't stall, steers fine and doesn't have air-con. ;)

Bugger that, for a daily i want aircon :thumbsup: All i gotta do is figure out an A/C fan to replace the stock one as the Plazmaman intercooler is so much thicker than my old ARC :cool:

Quick question for those with FFPs and stock bovs, where are you relocating your bov to and how did you do it? I'm currently thinking about what I'm going to do with my stock GTR bov. Ideally I'd like to keep it, but if it's too much hassle/cost then I am considering just ditching it. As I understand it, the closer to the TB the better, yes? What about flanges, where can I get a weld on flange?

Quick question for those with FFPs and stock bovs, where are you relocating your bov to and how did you do it? I'm currently thinking about what I'm going to do with my stock GTR bov. Ideally I'd like to keep it, but if it's too much hassle/cost then I am considering just ditching it. As I understand it, the closer to the TB the better, yes? What about flanges, where can I get a weld on flange?

My fabricator put the bov near the ffp and it vents to atmosphere ( I have a G4 Link with a MAP sensor). I hate the sound. I plan to relocate it to the other side (hot side) of the intercooler so I can plumb it in. I will need a long vacuum line so may make up a hard line.

No nearer the T/B is not better. Garrett actually say as close as possible to the turbo. I am sure there will be a fluid dynamic engineer or suchlike who can correct me but my take is that bovs are not about flow but about pressure relief and so it doesn't matter where it is. Some manufacturers put them on the intercooler itself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
×
×
  • Create New...