Jump to content
SAU Community

Recommended Posts

Article reckons it would be a Altima FWD sedan converted into a RWD with a 5.0L V8 dumped in it... why not just use a Skyline sedan with a V8 from the current Patrol/Infinit M56 that produces 420hp from a 5.6L V8? Regulations stipulate it has to be bored to 5.0L but still, would be better than an Altima surely?

Bring on the German powerhouses too, would love to see an M3 or C63 brought in. Then I'd definitely watch it.

should piss alot of holden & ford boys off - don't forget when scaife & (can't remember other blokes name), was it richards? they got boo'd when they accepted the winners podium spot

I remember that when I was a kid. Thought it was a bit crap even back then.

just wait till this nissan car starts winning races then all the bogan's will have a common thing to hate

holden fanbois ............... WE HATE FORD

ford fanbois ............... WE HATE HOLDEN

then it dawns on them - we both love to stand round in our thongs with our best stubbies on with a can of VB in our hands burning down port-a-loo's, we can be friends and hate the nissans!!!

holden AND ford bogans ............... WE HATE NISSAN'S... AGAIN!!

Because the Skyline has no local market relevance for Nissan.

They will have Infiniti here in September, so it would just be based on an Infiniti G (Skyline) or M (Fuga) sedan. The car will have no relevance to anything sold locally anyway since the Altima is FWD and a V6, so I don't see why the wouldn't use a different chassis too.

I don't get this assumption that Nissan headlights are going to make exactly the same car miraculously quicker than Holden and Ford headlights.. Or that they are going to run a Nissan motor, where are they going to fit pushrods in any of the Nissan motors?

As far as i know COTF has no specified capacity limitation but they have proposed a parity development system for a range of capacities.

The only requirement is that it be a naturally aspirated V8. The aim was to open the field up to the Euro marques selling hipo V8 sedans.

The race car must be 4dr body with RWD and have the external appearance of the street car.

The chassis, floor pan, steering, suspension, brakes, gearbox, wheels, tires, aero, etc. are all control so the racing will remain very competitive.

More importantly it will also remain very affordable and relevant, costing < $250,000 per car.

Nissan currently run two very successful NA V8 racing powerplant programmes, one in partnership with Zytek. All the series they currently

take part in use fairly aggresive intake restriction to limit power output, this means that V8SC will be the first time we see these powerplants opened up.

From what I recall the Nissan/Zytek VK45 is capable of 580Nm and between 600 and 700hp (unrestricted) depending on race length. The VK56 obviously

takes that further and you could run similar power at a reduced cost with increased durability.

With Ford's involvement sitting precariously at the moment, the departure of one make (in a two make series) will sound the death knell for the series.

COTF is their strategy for obtaining much needed diversity in their investor pool. There really is no other path to take without killing the series.

I'm looking forward to the 2013 season. I suspect there will be some interesting reactions from the fans and one or two news making moments

if Nissan makes it to the podium.

Gotta say, I've seen no Holden/Ford bogans up in arms over this. Maybe they haven't seen the news yet, or I'm reading all the wrong forums, but so far all I've seen is Nissan fans assuming/laughing at how pissed off the er...biased bogans...are supposedly going to be about it all. Probably not realising that it brings them down to the same level as your average "Go Ford!" or "Yeah Holden!" punter, when they start going on about it like that. Add to this, widespread ignorance of the fact these Nissans will be nearly identical to their Ford/Holden counterparts...and us Nissan fans start looking pretty stupid...like the drunk morons who perpetuate the existing V8 supercar fan stereotype. So, thanks! :(

  • 2 weeks later...

As far as i know COTF has no specified capacity limitation but they have proposed a parity development system for a range of capacities.

The only requirement is that it be a naturally aspirated V8. The aim was to open the field up to the Euro marques selling hipo V8 sedans.

In Auto Action, V8 Supercars were quoted as saying they wanted to stick to a 5L displacement, but this wasn't a rule yet. I think they're keeping their options open at this stage.

Gotta say, I've seen no Holden/Ford bogans up in arms over this. Maybe they haven't seen the news yet, or I'm reading all the wrong forums, but so far all I've seen is Nissan fans assuming/laughing at how pissed off the er...biased bogans...are supposedly going to be about it all. Probably not realising that it brings them down to the same level as your average "Go Ford!" or "Yeah Holden!" punter, when they start going on about it like that. Add to this, widespread ignorance of the fact these Nissans will be nearly identical to their Ford/Holden counterparts...and us Nissan fans start looking pretty stupid...like the drunk morons who perpetuate the existing V8 supercar fan stereotype. So, thanks! :(

You sir, need to go to the Kelly Racing Facebook page and see all the Holden bogans going nuts about it. Some of the stuff.. geeze... they need a sit down.

i gotta say its good to see kelly racing apparently have full backing by nismo japan in building their new cars!

and at the end of the day, with the COTF program the series will be very tight with so much being controlled, that even more so then ever it will be down to drive ability not so much the better car.

would be awesome to have a nismo/ motul car in the field!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...