Jump to content
SAU Community

Recommended Posts

  • Replies 93
  • Created
  • Last Reply

Top Posters In This Topic

Is there a place in Clayton called MV Automatics?

They have been recommended to me but i cant find them on google in Melbourne.

Seems they are in SA.

Anyone know?

Cheers

MV Auto is in SA...

I had my shift kit done at RVO Auto in Dandenong....they should be able to help you out if you can't find anyone else...

Oops just read the whole thread and saw that you already went to RVO.

I didn't have any issues with RVO. They changed my valve body over too. However I brought my own Matic J along as I didn't know wtf they were goig to put int.

Aaron (who used to have an ARX) also had his trans done at RVO and insisted on Nuon ATF.

Seems like they've done a few M35 by now...so you'd think they'd know NOT to use Dex III stuff...you'd hope.

Edited by ironpaw

Going back to RVO next week for a look in the pan.

It sounds like it"s going to cost anywhere between $300 and $1500 depending on what they find.

If they suggest closer to the high end I've got a box with 80,000K on it lined up.

Quoted $1,800 installed and I'll get the car dealer to go halves.

Just worried the dealer will want to refund my money on the car and take it back, fix the box and re-sell the car for a higher price.

You know I got it cheap :whistling:

MV Auto is in SA...

I had my shift kit done at RVO Auto in Dandenong....they should be able to help you out if you can't find anyone else...

Oops just read the whole thread and saw that you already went to RVO.

I didn't have any issues with RVO. They changed my valve body over too. However I brought my own Matic J along as I didn't know wtf they were goig to put int.

Aaron (who used to have an ARX) also had his trans done at RVO and insisted on Nuon ATF.

Seems like they've done a few M35 by now...so you'd think they'd know NOT to use Dex III stuff...you'd hope.

Is this Aron's old car i wonder?

Silver AR-X with Beige leather?

Didn't own it very long and traded it in at Holden?

If you use the gear box only in manual mode the oil will get very hot as when in manual mode the fluid does NOT go through the radiator to cool. It only goes through the radiator when in Auto mode.

If you overheat the gear box it will not shift down easily.

A transmission cooler is a great addition for our climate and some thing most of us have installed.

Cheers

Andy

Forgive my ignorance with this question as I'm yet to fit a transmission cooler...

If you put a cooler on the transmission don't you use the lines that loop through the radiator?

If this is the case the cooler still won't work when in manual mode?

This would make the cooler pointless when you're having a spirited drive in manual mode wouldn't it?

Is there a way around this?

Cheers,

Jas

So glad I haven't fitted my TransGo kit yet. On the cards when I get back.

Anyone know where you can buy this kit? I'm having a search around and not finding anything that concrete...

EDIT: Motospecs are one of the Australian distributors, part of the Repco group. I'll chase them up for a price this week. Online lead: http://www.makcotransmissionparts.com/63741-07K.html

hmmm....some more reading!!!

I read the pdf on this part and it was only needed in gearboxes with wear on the cooler valve. There was a wet test to see the condition.

This kit just provides a better seal where it need resurfacing.

Yep. Just read that PDF. This kit isn't what I was thinking it was. Atleast I don't need to rip out the valve body again.

So is there a way to have fluid running through the cooler when in manual mode at all then?

Edited by slippylotion

Cam seems to think it does, perhaps we could get a few people to test by driving in manual and carefully checking the temp the trans cooler gets to? If its not ccoling I would be surprised.

I drive in manual constantly so I will try and check sometime too.

So why do guys think it doesn't cool the fluid when in manual mode? Did they find something in a manual stating it doesn't or just a hunch?

How are you checking oil temps in the trans, Do you have an a/market gauge fitted?

I'm keen to know the outcome on this as I never use manual mode as too worried I'll over heat the trans.

Edited by slippylotion

I "tested" it by going on a long drive in manual mode when I was running the PWR and Mishimoto trans coolers in series (no radiator in tank regulator), both of which were mounted on brackets and not touching the radiator at all.

Was curious as to how hot the coolers got so did the drive and put my hand on the PWR cooler when I got back. It was quite warm. The only time the car was out of manual mode was when reversing out of the driveway.

Scientific? No. Logical? To me, yes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...