Jump to content
SAU Community

Recommended Posts

spotted RUNVS 2(?) on Main North Rd/ Robe Tce(?) intersection today

around 3:15pm

oh and a silver R32 with a white front left quarter panle

going into KFC/HJ car park around 3:00pm, think it was near Unlety Shopping Centre

not to sure

Edited by pokie
  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

small world Hey Cara fancy you knowing my mate :laugh:

i was so surprised! havent seen shannon in aaaagggeeeess! hasnt changed since i saw him last !!! LOL!

and yes the world is getting much smaller

spotted Kye (DRTY 2) last night around midnight driving past the seaford tav, i was with the group of people that may have looked a little drunk and disorderly! hehe!

:laughing-smiley-014:

was that your bright white ass that was being flashed to the poor fella's in the other car haha

i believe my missus saw that and is now alitte scared haha

good to see your keeping it loose :) was out at wickhams hill then went to get fuel and unfortunetly decided to drive past the seaford tav and saw abit of ass, i shouldnt have looked in my rear view mirror :action-smiley-069:

kye

Yeah i was up there watching, wouldnt miss it.

Ontheranch - was it u i spotted maybe a week or so ago coming off of hindley street? Was in the orange 32, not sure if i was driving or my bf but got a wave from a chick in a silver 34, thinking maybe it was u?

Yeah i was up there watching, wouldnt miss it.

Ontheranch - was it u i spotted maybe a week or so ago coming off of hindley street? Was in the orange 32, not sure if i was driving or my bf but got a wave from a chick in a silver 34, thinking maybe it was u?

Yeah that was me!

Sweet 32 bytheway

Cheers, likewise with your car :yucky:

Was surprised actually lol, most times i go to wave at a chick in a skyline i get ignored.. i waved back not sure if u saw me though.

Haha some ppl have their head up their ass. I always wave :)

spotted flick going from morringe ave turning onto morphet rd today and back again.

looks nice :D

Were you in your car? cos i didnt see u! :)

Spotted my bf Luke and fishpaste luke pushing his Gtr yesterday :P

Cos he forgot he had to turn off the immobiliser :(

Were you in your car? cos i didnt see u! :D

Spotted my bf Luke and fishpaste luke pushing his Gtr yesterday :)

Cos he forgot he had to turn off the immobiliser :(

nah i was at work

While meeting up with Madaz after work, spotted at the Hancock Rd & Nth East Rd intersection 'absent' (TuffR32) & Shazza (her200sx). Also, a wave from (BW) Troy in his WRX as we went passed each other in Modbury.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...