Jump to content
SAU Community

M35 Attesa Ets "pressure Switch" Problems

slippylotion
 Share

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Erop
Erop

you may be interested - in cold Russia the most suspicious part of ATTESSA is used to be the pressure control switch, which causes C1208 error reading this is one of this crap pieces it's not

Erop
Erop

this switch is only marked with PS-20 the WAKO doesn't sell less than 1000 pcs now looking for byuing this switch, still no exact code, Scott's right BUT - you may take it from R32-R34, Laurels,

Posted Images

slippylotion Mentor

slippylotion

Posted
  • Author
Posted (edited)

Well I got a call back toady after the pump assembly was tested and it's f@cked. The pressure switch and accumulator are shagged and the motor itself is chewed out with the impeller chewing on the inner casing all due to the pressure switch sticking on.

So I'm getting a change over reconditioned assembly ex Japan for $1920 to my door from Hills Motorsport. The new pump is the late updated model with a better pump design and Pre filters fitted. Only catch is its a 30 day wait from Japan then for Hills to bech check and set it up then post to me, I'm expecting to wait about 6 weeks until I can refit it. Still could have been worse as its the last ready unit on the shelf.

Edited by slippylotion
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Well I got a call back toady after the pump assembly was tested and it's f@cked. The pressure switch and accumulator are shagged and the motor itself is chewed out with the impeller chewing on the inner casing all due to the pressure switch sticking on.

So I'm getting a change over reconditioned assembly ex Japan for $1920 to my door from Hills Motorsport. The new pump is the late updated model with a better pump design and Pre filters fitted. Only catch is its a 30 day wait from Japan then for Hills to bech check and set it up then post to me, I'm expecting to wait about 6 weeks until I can refit it. Still could have been worse as its the last ready unit on the shelf.

I might have a spare assembly soon, not sure on the condition yet. That sounds like an expensive rebuild to me...

slippylotion Mentor

slippylotion

Posted
  • Author
Posted

I wouldn't say its expensive seeing as the accumulator is around $350 trade price alone and about $200 for a pressure switch that you can't actually buy from Nissan then the cost of a new pump that again you can't buy separate from Nissan and I need the complete assembly. Nissan only sell the complete pump assembly for $5k trade. New pump assembly in Japan is around 200,000yen from Nissan. These are rebuilt in Japan but with Australian warranty from Hills Motorsport. Im not keen to take the chance on a s/hand pump as it could go a week later. Atleast with this I have a warranty and shouldn't have any further problems for the 5 ish years Ill keep the car.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Im not keen to take the chance on a s/hand pump as it could go a week later. Atleast with this I have a warranty and shouldn't have any further problems for the 5 ish years Ill keep the car.

Yep, I agree it would usually be the best option but at that price? Its not like everyone else is replacing them, they are quite reliable in most cases. It's you coin buddy...

slippylotion Mentor

slippylotion

Posted
  • Author
Posted

Yeah I agree its a lot of coin but it seems the cheapest way to fix it correctly and completely. I though of a second hand unit but they sell for $700-900 so if it dies in a year or two its really half the cost of the fully rebuilt assembly wasted seeing as a new unit should last another 10 years or so.

Id probably guess that the other guys getting the pressure switch fault code or 4WD randomly coming on are probably in the same boat. I asked why my torque gauge would still read if the pumps shagged and he said its a theoretical reading via the G sensor not the actual pump pressure. While the gauge is showing front drive it may well not be actually getting it.

zei20l Grand Master

zei20l

Posted
Posted

$700-900 for 2nd hand? massive rip off

i have a complete unit here you can have for $150. no idea if/what is wrong with it. but it might be a hell of a lot cheaper to pull bits off than 2k for a 'new' one

slippylotion Mentor

slippylotion

Posted
  • Author
Posted (edited)

Thats cheap. Theres one on Yahoo at 25000 yen so far then postage and fees it will be around $400-500.

I know $1900 seems like a lot but I don't want to have another problem with it again while I have the car. I suppose its similar to replacing a turbo with a cheap stock unit, bound to go at anytime so might as well just go a new one.

I also just double checked the oil I bled out of it last week while flushing some through and found all the little metal fillings in it. Just a bummer all 3 parts of my pump assembly died :angry:

Edited by slippylotion
  • 1 month later...
Sage222 Rising Star

Sage222

Posted
Posted

any more news on this one guys? i am wondering if my attessa has the same problem :( i have the same dashboard dimming and the front torque guage blip issue when the 4WD light is off.. when the 4WD light is on all is smooth.

though i think ill remove shafts and disable the pump rather than spend a heap of coin on fixing it..

ironpaw Veteran

ironpaw

Posted
Posted

nothing? :(

I had this issue...4WD light coming on intermittently, the ATTESSA pump chirping away...

I had a dead battery a month ago and replaced the battery, left the battery unplugged for a week.

Started driving again last Wed and haven't seen the 4WD light on yet...so not sure wtf the problem is...pump hasn't been chirping like mad either...

ironpaw Veteran

ironpaw

Posted
Posted

wow that sounds like a cheap fix :) maybe ill give it a shot this weekend :))

LOL you gonna disconnect the battery for a week?

TBH I think the problem will resurface after a few more weeks, maybe once the car is driven daily the strain on the ATTESSA system will probably cause it to come back...

Sage222 Rising Star

Sage222

Posted
Posted

awesome thanks Scotty will hit them up if import factory dont come through. what did they sting you for a read? can they translate the codes for you? and one last thing if the light doesnt happen to be on will they still be able to get it?

[END SPAM QUESTIONS]

:)

scotty nm35 Grand Master

scotty nm35

Posted
Posted

They only checked it, and told me the codes, they were in english and self explanatory as I remember. Give them a call and ask, tell them Scott sent you down.

The tcu doesn't show the codes with a malfunction lamp, that is for the engine only I think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • luke gtr
      G'day!

      By luke gtr · Posted

      Welcome. Dont let anyone dissuade you from your dreams. If you want a gtr, keep sabing and you will eventually get one. I feel like if I had have bought stocks, those companies would have gone bust and I would have lost my money.  There's a gamble in everything we buy. I've had good times and bad. But... I've also met my absolute best friend through this network and can't imagine life without them(more like a brother). Keep in mind, some specific mods will change as technology gets better. If you feel like general chat, there's always the wasteland.....
    • soviet_merlin
      Japan Scrapbook

      By soviet_merlin · Posted

      Those are some very cutesy barriers! Is that common?
    • Rezz
      Japan Scrapbook

      By Rezz · Posted

      Saw this abandoned Honda Fit in a carpark that was getting repaved... they just 'cut around it' and continued with the job! There's a number of reasons why the car could have been abandoned, but as for the construction company, legally they don't have permission to move the car from the owner (who has moved on and can't be contacted) so all they can do it just leave it there with enough space around it so it won't get damaged. 
    • r32-25t
      Rb26/30 build

      By r32-25t · Posted

      You’ll want to have the block drilled and tapped to suit 1/2in head studs and the head for the same. How much power do you intend to make?
    • hoodedreeper
      Chris' R34 GTT Series 2

      By hoodedreeper · Posted

      Sorry for resurrecting an oldish thread Not much has happened in the past year since the last update. The car did another 1000 miles or so and failed the MOT for the first time in October (failed on tyres which had been advised for a couple of years) In October the car got put up for sale and was removed in November due to no interest, being so close to christmas it was to be expected. The roads were dry in February so I decided to tax it early and get the new tyres fitted.   Fast forward to April, I got someone in to give the car a good clean after sitting for the winter.                                 The car got re-advertised and today (Saturday 3rd May) the car sold. The new owner is planning a GTR conversion at some point and a respray in the same pearl white. It's bitter sweet, it's a shame to have the car sit there for half the year and then only do 1000 miles. The kids are growing too quick and space in the back is getting limited. It's been a great 6.5 years of ownership
×
×
  • Create New...